It's hard to imagine a modern car without a rear view camera. If your car does not have this option from the factory, then you can install the camera yourself. The “Lux” configurations of Lada Granta, Kalina 2, Priora cars have similar multimedia systems (MMS), so the process of connecting and setting up the camera is identical. During installation of the camera, there may be differences depending on the type of body (hatchback, station wagon, sedan, liftback), but they are insignificant.
Lada Granta - installing a rear view camera
Due to the fact that a 2-DIN Chinese radio was purchased, I was honored to install a rear view camera. The radio came with a rear view camera, which had to be mounted on the outside of the trunk door. I was too lazy to run “kilometers” of wires along the trunk lid, rear pillar, disassemble the ceiling, and the sides of the trunk, so, after surfing the Internet, I found a camera that fits into the bumper, like parking sensors (much closer to the reversing lights). Installation in the bumper is the same as when installing parking sensors, instructions are here. A cutter of suitable size is included in the kit. The liftback has two reverse lights, so I connected the camera to the second one (the parking sensors are connected to the first one). The cameras came with wires. Connection diagram:
connection diagram
Connector P2 – red wire to + reverse lamps, black – ground.
The signal wire from the camera to the radio (which has tulip connectors) has another additional red wire P3. This is the power supply for the radio to output images from the camera. We connect one end to the + of the reverse light, the other to pin 9 of the radio connector (red dot on the ISO connector of the radio). Since birth, I had audio equipment in my car, but this wire was not in the block. I pulled the wiring out of the block that came with the radio and inserted it into the ISO block of the car. The wire was thrown under the carpet, the tulip is connected to the CAMIN connector on the radio.
connection
This is what happened on the screen
inside
This is what it looks like from the outside
outside
outside2
The rear view camera automatically turns on when you engage reverse gear, and also turns off automatically. If music or navigation is turned on, it turns off, then, when the camera is turned off, it turns on accordingly. An unpleasant feature is that at night, when driving in a narrow space, you still need to look in the mirrors; the glowing radio screen from the camera on is blinding. I found a solution: first turn on the radio or music, while the music is running, forcefully turn off the screen with the button in the upper right corner (the radio has a function that switches to day or night brightness (there is almost no difference between them) or turns off the screen), turn on reverse - image with The cameras are not displayed and you can safely move along the mirrors. I don’t know yet how quickly the camera will get dirty in this location, but I think wiping the camera is not a big problem. But the camera is positioned exactly in the center of the car and the image is not shifted anywhere.
Installing a rear view
for Lada Granta, Kalina, Priora and Vesta
It's hard to imagine a modern car without a rear view . Not much help for people who are looking for how to install a rear view camera on. AvtoVAZ understands this, which is why it equips the “luxury” version of the Lada Vesta with such an accessory. The following describes how to install
rear view
camera on a Granta liftback and connect it to the standard radio (MMC), but similar instructions are also suitable for other Lada cars.
Rear view camera installation steps
Let's look at the detailed instructions on how to install a rear view camera if you choose a location above the rear bumper of the car, connected to the built-in Pioneer monitor.
Preparing the site for camera installation
The chosen location for connecting the camera has several advantages. First of all, a wide viewing angle and the absence of disturbing parts. However, there is also a minus. The camera remains “on the street” and is accessible to strangers. Therefore, this option is suitable for car owners with garages, or if the block above the license plates is more recessed, thereby creating a place to hide the camera. You must first secure the camera bracket by drilling 4 holes for mounting and 1 for the power cable.
Power connection
The most critical stage is connecting the car to the general electrical network. If you do not have experience in such work, then it is better to contact a specialist so as not to damage the device. If there is a general understanding of how and what works, then you need to follow these steps.
Any camera has two wires: for power and for transmitting a video signal. Since most cameras have short wires, they need to be extended so that they reach the monitor. Extension cords are often included.
The power is most often connected to the tail lights. Thus, simultaneously with the reverse gear being engaged, the camera will also turn on.
Wiring cables inside the car
All wires must be routed through the trunk and interior, hidden, to avoid breakages. This can be done in two ways: either secure everything under the casing, or secure the wires with special clamps.
The advantage of the first option is that the wires will not be visible, however, this method requires a more detailed and large-scale disassembly of the car, which not everyone wants.
The second method is easier and faster, but there is no full guarantee of the absence of breaks.
Installation
Required:
- view camera , see AliExpress catalog.
- mini ISO connector (blue block and tulip).
- several meters of wire.
Most often, the rear view camera is placed above the license plate (on an overlay called “saber”). How to install fog lights on a Lada Granta. -. This location is the most favorable from a viewing point of view; the camera is not noticeable and there is no need to remove the bumper. How to install a radio on a Priora with your own. First, remove the trunk lid trim, and then the saber, which is held on by 6 M8 screws.
We determine the most suitable place for the camera and drill a hole there. How to Connect a Rear View Camera to a TV. We secure the accessory on the reverse side with a nut.
How to choose a good camera. Review of prices from different manufacturers
| № | Article/name | Price, rub.) |
| 1. | Kalina, Kalina-2, Granta (liftback), Vesta, Priora |
Read more: How to update the Navitel program on your navigator
*prices are current as of 09/24/18.
Technical characteristics of the rear camera of the Grant Liftback:
- Matrix type: CCD (photosensitive);
- Viewing angle: 170°;
- Resolution 800 x 600 pixels;
- Zoom level: 0.01 Lux;
- Aspect ratio: 4:3;
- Gradation: parking lines on the screen (0.5 / 1.0 / 1.5 meters);
- Moisture and dust protection: present, level IP 67;
- Brightness: 300;
- Recommended voltage for correct operation: 12V;
- Operating temperature range: - 25° - + 35°;
- Connection type: ISO connector, from the back of a 2-DIMM radio or a separate folding monitor.
The most popular gadgets are in the price category up to 1,500 rubles. Picture display quality, focusing, zoom level are at an average level. Of course, the image is grainy, pixels are visible, and the viewing angle is only 170 degrees.
The rear view camera on the Granta Liftback in the range of up to 3,000 rubles has improved characteristics, image output quality, and a viewing angle of 180°. Despite decent parameters, gadgets in this price category are beyond the means of most car owners.
Setting up standard MMS
No firmware required for the radio, you just need to activate the rear view camera
. To do this, download the program (To download files you need to log in to the site) and copy it to removable media (USB Flash).
- Go to the desktop (WinCE). On the radio screen, hold down the “Settings” button, then “Exit” and “Desktop”.
- Let's launch the program. how to connect a rear view camera to a TV Connecting a rear view camera Installation of the camera should provide a good overview, parking lot markings should be visible for convenience. Rear view camera Lada Warranty on the camera is an indispensable assistant for both. How to install a turbine on a Zhiguli? My device - USB disk - Folder with the program - Run the CamOnOff file.
- We allow you to use the camera . Click on the corresponding button. We close the program, it and the flash drive will no longer be needed.
By the way, the whole process is also shown in the video:
Checking the operation of the rear view
including reverse gear.
Let us remind you that some motorists prefer to use parking sensors instead of a camera.
Rear view camera on the fret of the grant - installing the necessary accessory
LadaOnline 93 777 6 It is difficult to imagine a modern car without a rear view camera. AvtoVAZ understands this, which is why it equips the “luxury” version of the Lada Vesta with such an accessory. The following describes how to install a rear view camera on a Granta liftback and connect it to the standard radio (MMC), but similar instructions are also suitable for other Lada cars. The “Lux” configurations of Lada Granta, Kalina 2, Priora and Vesta cars have similar multimedia systems (MMS), so the process of connecting and setting up the camera is identical. During installation of the camera, there may be differences depending on the type of body (hatchback, station wagon, sedan, liftback), but they are insignificant. Installation You will need:
Preparation for installation
Before installing a rear view camera on a car, you will need to remove several trim elements of your vehicle. You should start working only if you have at least basic knowledge of electrical wiring. It is especially important to remain calm when working with plastic elements, because haste in this matter can lead to unpleasant consequences.
First of all, you should inspect the “front of work” and install all the latching points, as well as locate all the fasteners. This will allow you to quickly and easily prepare the car for installation of this device using ordinary screwdrivers. In addition, it should be remembered that any work on the vehicle’s electrical wiring must be carried out after the battery has been completely disconnected.
How to install a rear view camera on a grant
Do-it-yourself wiring and connection of wires You can run wires into the cabin to the standard multimedia system either through the headliner or along the side door trims. To work with ceiling cladding, we recommend using special “spatulas” and filling the voids under the cladding with additional pieces of foam rubber for the cable. On the A-pillar, the wire can be connected to the antenna wire, then stretch it to the glove compartment area to the radio or standard multimedia. The central panel is attached to metal clips and can be removed quite simply. To do this, you need to insert a flat-head screwdriver into the hole on top of the radio and pry it off, then disconnect several clamps. After this, remove the temperature and air direction regulators and use a screwdriver to unclip the fasteners along the perimeter of the panel from top to bottom. It is most convenient to connect the camera power wires to the reversing light.
Procedure for installing the rear camera on the Granta liftback
- We place the car on a flat area.
- Remove the rear door trim.
- Remove the driver's and passenger's door sills on the left side.
- We lay a block with wires from the center console to the rear door lid.
- We dismantle the saber - spoiler.
- We install the mount.
- We connect the wiring to the 2-DIMM radio.
The order may differ from the above. In the event that the owner does not want to display the image on the standard radio. In this case, use a folding monitor. The location of fixation is arbitrary.
Preparatory stage
- isolation;
- screwdrivers with different tips;
- plastic spatula for plastic;
- blocks with wires;
- adapter - ISO type connector.
Dismantling works
- remove the thresholds from the left driver and passenger doors;
- fold the back row of seats;
- remove the upper trim of the interior and luggage compartment;
- Unscrew the fasteners, remove the spoiler from the trunk lid.
Laying wires, power supply from the circuit
We lay the wiring from the central channel of the console to the trunk lid along the following route:
- location for fixing the standard radio,
- the lower part of the dashboard on the left side under the steering wheel,
- thresholds,
- rear door pillar,
- luggage compartment lid.
Connection to the power circuit from the positive cable of the reverse gear lamp. In the Lada Granta Liftback it is green and located in the luggage compartment on the right side. Powering is done by soldering; twisting is also permissible, provided that the connection point is well insulated.
Read more: Timing kit Renault Symbol
Installing a rear view camera on a grant
If music or navigation is turned on, it turns off, then, when the camera is turned off, it turns on. An unpleasant feature is that at night, when driving in a narrow space, you still need to look in the mirrors; the glowing screen of the radio, from the turned on camera, is blinding. I found a solution: first turn on the radio or music, while the music is running, forcefully turn off the screen with the button in the upper right corner (the radio has a function that switches to day or night brightness (there is almost no difference between them) or turns off the screen), turn on reverse - image with The camera is not displayed and you can safely move along the mirrors. I don’t know yet how quickly the camera will get dirty in this location, but I think wiping the camera is not a big problem. But the camera is located exactly in the center of the car and the image is not shifted anywhere.
Lada granta - installation of a rear view camera.
Connection General diagram for connecting a rear view camera: In the trunk, connect the camera to the rear light wiring:
- +12V to green wire (reverse)
- "mass" to black
We connect the miniISO connector to the radio, the location of the wires in the blue block is as follows:
- Ground (outer part of the tulip) of the connector to pin 16.
- Plus (central part) of the connector to pin 19.
It is worth noting that if the MMC was installed on a car in the “norm” or “standard” configuration, then you will need to additionally supply +12V from reverse to pin No. 1 of connector A1 of the radio. The process is also shown in the video: Setting up a standard MMC No firmware is required for the radio, you just need to activate the rear view camera. To do this, download the program (To download files you need to log in to the site) and copy it to removable media (USB Flash).
By karpoff
Home Car repair - useful articles Lada Granta liftback - reviews, repair Lada Granta installation of a rear view camera Due to the fact that a 2-DIN Chinese radio was purchased, I was honored to install a rear view camera. The radio came with a rear view camera, which had to be mounted on the outside of the trunk door. I was too lazy to run “kilometers” of wires along the trunk lid, rear pillar, disassemble the ceiling, and the sides of the trunk, so, after surfing the Internet, I found a camera that fits into the bumper, like parking sensors (much closer to the reversing lights).
Installation in the bumper is the same as when installing parking sensors, instructions are here. A cutter of suitable size is included in the kit. The liftback has two reverse lights, so I connected the camera to the second one (the parking sensors are connected to the first one). The cameras came with wires. A rear view camera is a convenient and practical accessory that greatly helps when parking. Only luxury models are equipped with cameras at the factory; owners of other versions have to install this accessory themselves. A way to find out why the CHECK light is on! Using a universal auto scanner, you can do the diagnostics yourself in 2 minutes and find out why CHECK is on. Suitable for all cars..." Read more 1 How to choose a good camera and a convenient installation method? There are a huge number of models of rear view cameras on the market that are suitable for both the Granta and other VAZ models, including the Lada Priora and Lada Vesta models. We are talking about universal options of domestic and Chinese production. Car radio - https://got.by/ixf0h Rear view camera - https://www.citilink.ru/catalog/car_electronics/backup_cameras/374601/ Lada Granta - we are looking for a live one NOT expensive.. Resale Nizhny. Car service: 'Lada Granta or Lada Priora? how to install the rear-view camera. Detailed instructions on how to install the rear-view camera. Installation of dirt-proof plugs for the steering rod opening.
Lada Granta. Lada Kalina soundproofing and music. PI%DEC. WHAT I FOUND FOR LADA GRANT ON ALIEXPRESS! LaGranta - Rear passenger lamp. Selection and installation of car rear view cameras. Used Cars | Lada Granta | 2012. UBER on LADA GRANTA. zero, first maintenance on the Lada Granta (liftback) is it worth going to the officials? Installing Parktronic with Your Own Hands from Sergei Zaitsev. 7 Driving Habits That Destroy Your Car and Empty Your Wallet. Lada Granta and the Far East, the Chinese said the Chinese made it.
