October 23, 2015 Lada.Online 203 573 37

It's hard to imagine a modern car without a rear view camera. If your car does not have this option from the factory, then you can install the camera yourself. The “Lux” configurations of Lada Granta, Kalina 2, Priora cars have similar multimedia systems (MMS), so the process of connecting and setting up the camera is identical. During installation of the camera, there may be differences depending on the type of body (hatchback, station wagon, sedan, liftback), but they are insignificant.

Lada Granta - installing a rear view camera

Due to the fact that a 2-DIN Chinese radio was purchased, I was honored to install a rear view camera. The radio came with a rear view camera, which had to be mounted on the outside of the trunk door. I was too lazy to run “kilometers” of wires along the trunk lid, rear pillar, disassemble the ceiling, and the sides of the trunk, so, after surfing the Internet, I found a camera that fits into the bumper, like parking sensors (much closer to the reversing lights). Installation in the bumper is the same as when installing parking sensors, instructions are here. A cutter of suitable size is included in the kit. The liftback has two reverse lights, so I connected the camera to the second one (the parking sensors are connected to the first one). The cameras came with wires. Connection diagram:

connection diagram

Connector P2 - red wire to + reverse lamps, black - ground.

The signal wire from the camera to the radio (which has tulip connectors) has another additional red wire P3. This is the power supply for the radio to output images from the camera. We connect one end to the + of the reverse light, the other to pin 9 of the radio connector (red dot on the ISO connector of the radio). Since birth, I had audio equipment in my car, but this wire was not in the block. I pulled the wiring out of the block that came with the radio and inserted it into the ISO block of the car. The wire was thrown under the carpet, the tulip is connected to the CAMIN connector on the radio.

connection

This is what happened on the screen

inside

This is what it looks like from the outside

outside

outside2

The rear view camera automatically turns on when you engage reverse gear, and also turns off automatically. If music or navigation is turned on, it turns off, then, when the camera is turned off, it turns on accordingly. An unpleasant feature is that at night, when driving in a narrow space, you still need to look in the mirrors; the glowing radio screen from the camera on is blinding. I found a solution: first turn on the radio or music, while the music is running, forcefully turn off the screen with the button in the upper right corner (the radio has a function that switches to day or night brightness (there is almost no difference between them) or turns off the screen), turn on reverse - image with The cameras are not displayed and you can safely move along the mirrors. I don’t know yet how quickly the camera will get dirty in this location, but I think wiping the camera is not a big problem. But the camera is positioned exactly in the center of the car and the image is not shifted anywhere.

How to install a rear view camera on a grant

Do-it-yourself wiring and connection of wires You can run wires into the cabin to the standard multimedia system either through the headliner or along the side door trims. To work with ceiling cladding, we recommend using special “spatulas” and filling the voids under the cladding with additional pieces of foam rubber for the cable. On the A-pillar, the wire can be connected to the antenna wire, then stretch it to the glove compartment area to the radio or standard multimedia. The central panel is attached to metal clips and can be removed quite simply. To do this, you need to insert a flat-head screwdriver into the hole on top of the radio and pry it off, then disconnect several clamps. After this, remove the temperature and air direction regulators and use a screwdriver to unclip the fasteners along the perimeter of the panel from top to bottom. It is most convenient to connect the camera power wires to the reversing light.

How to choose a good camera. Review of prices from different manufacturers

*prices are current as of September 24, 2018.

Technical characteristics of the rear camera of the Grant Liftback:

• Matrix type: CCD (photosensitive);
• Viewing angle: 170°;
• Resolution 800 x 600 pixels;
• Zoom level: 0.01 Lux;
• Aspect ratio: 4:3;
• Gradation: parking lines on the screen (0.5 / 1.0 / 1.5 meters);
• Moisture and dust protection: present, level IP 67;
• Brightness: 300;
• Recommended voltage for correct operation: 12V;
• Operating temperature range: - 25° - + 35°;
• Connection type: ISO connector, from the back of a 2-DIMM radio or a separate folding monitor.

The most popular gadgets are in the price category up to 1,500 rubles. Picture display quality, focusing, zoom level are at an average level. Of course, the image is grainy, pixels are visible, and the viewing angle is only 170 degrees.

The rear view camera on the Granta Liftback in the range of up to 3,000 rubles has improved characteristics, image output quality, and a viewing angle of 180°. Despite decent parameters, gadgets in this price category are beyond the means of most car owners.

Rear view cameras / Rear view cameras

• Rear view cameras
• Rear view mirrors

It’s good when your Chevrolet, Honda, Hyundai or any other car is equipped with a rear view camera: this device makes parking easier not only for a beginner, but also for an experienced driver who has recently replaced his iron horse. The standard rear view camera for Ford, Kia, Mitsubishi and other cars is installed by the manufacturer, unfortunately, not on all models. Most budget Nissan, Opel, Suzuki models do not have this function.

But don’t be upset: a rear view camera can be installed on any car – Toyota, Mazda, Volkswagen – no matter what brand or year it is. These devices have different modifications and configurations. For example, they can be equipped with additional parking sensors. They also differ in the method of mounting: for expensive Lexus, Volvo or Chrysler, cameras made in the form of a frame for the rear license plate, in which the camera is combined with the license plate light, are suitable. It is possible to strengthen the camera under the bumper of Subaru, Ssangyong, Skoda.

In some cases, even insertion into the body of a Mazda or Volkswagen is allowed, but every year the installation becomes easier and easier and without changes in the design of the car.

It’s good when your Chevrolet, Honda, Hyundai or any other car is equipped with a rear view camera: this device makes parking easier not only for a beginner, but also for an experienced driver who has recently replaced his iron horse. The standard rear view camera for Ford, Kia, Mitsubishi and other cars is installed by the manufacturer, unfortunately, not on all models. Most budget Nissan, Opel, Suzuki models do not have this function.

But don’t be upset: a rear view camera can be installed on any car – Toyota, Mazda, Volkswagen – no matter what brand or year it is. These devices have different modifications and configurations. For example, they can be equipped with additional parking sensors. They also differ in the method of mounting: for expensive Lexus, Volvo or Chrysler, cameras made in the form of a frame for the rear license plate, in which the camera is combined with the license plate light, are suitable. It is possible to strengthen the camera under the bumper of Subaru, Ssangyong, Skoda.

In some cases, even insertion into the body of a Mazda or Volkswagen is allowed, but every year the installation becomes easier and easier and without changes in the design of the car.

Pages:

Models archive

• …

Procedure for installing the rear camera on the Granta liftback

1. We place the car on a flat area.
2. Remove the rear door trim.
3. Remove the driver's and passenger's door sills on the left side.
4. We lay a block with wires from the center console to the rear door lid.
5. We dismantle the saber - spoiler.
6. We install the mount.
7. We connect the wiring to the 2-DIMM radio.

The order may differ from the above. In the event that the owner does not want to display the image on the standard radio. In this case, use a folding monitor. The location of fixation is arbitrary.

Preparatory stage

• isolation;
• screwdrivers with different tips;
• plastic spatula for plastic;
• blocks with wires;
• adapter - ISO type connector.

Dismantling works

• remove the thresholds from the left driver and passenger doors;
• fold the back row of seats;
• remove the upper trim of the interior and luggage compartment;
• Unscrew the fasteners, remove the spoiler from the trunk lid.

Laying wires, power supply from the circuit

We lay the wiring from the central channel of the console to the trunk lid along the following route:

• location for fixing the standard radio,
• the lower part of the dashboard on the left side under the steering wheel,
• thresholds,
• rear door pillar,
• luggage compartment lid.

Connecting wiring, installing standard casing

After installing the camera, connect the positive cable to the flashlight wiring. We place the block with wires in a corrugated material made of fire-resistant material, and fasten the casing.

From the back of the 2-DIMM radio, we connect to the miniISO connector:

• black wire: ground;
• red: 12V power supply from the reversing light.

The designations on the plug are: pin 16 and pin 19, respectively. For the standard MMC radio, no additional firmware is required. The screen automatically switches to camera mode when reverse gear is activated. We start the engine, activate “R” gear, an image appears on the screen of the standard rear view camera.

Setting up standard MMS

No firmware required for the radio, you just need to activate the rear view camera

. To do this, download the program (To download files you need to log in to the site) and copy it to removable media (USB Flash).

1. Go to the desktop (WinCE). On the radio screen, hold down the “Settings” button, then “Exit” and “Desktop”.
2. Let's launch the program. how to connect a rear view camera to a TV Connecting a rear view camera Installation of the camera should provide a good overview, parking lot markings should be visible for convenience. Rear view camera Lada Warranty on the camera is an indispensable assistant for both. How to install a turbine on a Zhiguli? My device - USB disk - Folder with the program - Run the CamOnOff file.
3. We allow you to use the camera . Click on the corresponding button. We close the program, it and the flash drive will no longer be needed.

By the way, the whole process is also shown in the video:

Checking the operation of the rear view

including reverse gear.

Let us remind you that some motorists prefer to use parking sensors instead of a camera.

The Volzhsky Automobile Plant does not practice installing a rear view camera on its cars, so this process is carried out by car owners. Today we will tell you how to install a rear view camera on a Lada Granta with your own hands. You will need: a rear view camera, a knitting needle (wire) for pulling wires, a Phillips screwdriver. The easiest way to install a rear view camera on a Grant is to attach it to the bumper with self-tapping screws above the license plate. It is not necessary to remove the bumper for this. To route the camera wiring into the trunk, you will need to remove the left license plate light, and then pull the wires through the rubber plug using a long knitting needle. You will only have to remove the bumper on the Lada Granta if you decide to install a rear view camera inside the bumper. This placement of the camera will be more reliable, but installation time will also increase.

Reviews

Conclusion The standard screen displays the image from the rear view camera with a resolution of 800 x 600 pixels. Obviously, this is not a 1920 x 1080 HD format, but the picture is quite legible. Those wishing to improve output quality can additionally purchase a portable monitor for an additional fee.