Vacuum brake booster VAZ 2110

Troubleshooting the vacuum booster

Devices from different manufacturers may vary in characteristics and quality, and the price of the VAZ 2110 vacuum amplifier may also vary. Since the functioning of its mechanism affects the operation of other parts and components, and above all the car engine, it is worth not saving and carefully monitoring its serviceability.

If there is a hissing sound from under the hood, a burnt smell of oil is felt in the cabin, and the brake works like a stopped car only after repeatedly pumping the brake pedal with your foot, then you should immediately contact a car service center for diagnostics and, if necessary, replacement of this device.

You can test the “tens” vacuum brake booster for proper operation yourself. To do this, press the brake pedal repeatedly with the engine off. This method checks the uniformity of pressure in the cavities. Everything is fine as long as the valve body does not jam.

Then, when you hold your foot on the brake pedal, the engine starts. If the pedal is moved forward simultaneously with the foot, then the amplifier is operational. Otherwise, you need to make sure that the problem is this and not a problem with the tip flange or its fastening.

The pedal may still not function properly due to a faulty connection of the fitting on the engine exhaust pipe to the hose. This also has a detrimental effect on the performance of the braking system and its effectiveness.

Principle of operation

VUT, or as drivers say - vacuum cleaner, creates a vacuum, due to which additional force is created when the brake pedal is pressed. Thus, the vacuum booster ensures that when you press the pedal without applying much force, the brakes are applied quickly and effectively.

Vacuum brake booster

Such a system on the VAZ 2110 not only simplifies and speeds up wheel locking, but also contributes to less wear and tear on the vehicle and makes driving more comfortable. The “diagonal layout” of the vacuum brake, when the wheels are blocked due to two circuits (front right - rear left and front left - rear right) is designed so that even if one of the circuits fails, it is possible to brake quite effectively, and the car at the same time didn't skid.

VUT and GTZ Priora on VAZ 2110

You can improve the standard brakes of a VAZ 2110 in various ways, and in this photo report we will look at how to install a Vacuum Brake Booster (VUT) and a Brake Master Cylinder (MCC) from a Lada Priora or Kalina on a “top ten” with your own hands. Required:

VUT and GTZ Priora or Kalina
2 tees from classics
4 nuts x 8 for attaching the GTZ and pedal assembly to the VUT (the old ones are not suitable, they are larger)
One-face brake bleeding device.
2 tubes from Priora with fittings 12x1 and 10x1 on the GTZ side, and 10x1.25 on the tee side.
Brake fluid.

The photo shows:

On the left is the Prirovskaya tube 12x1.0, and on the right is the “tens” 10x1.25
On the left is a VAZ 2110 10x1.25, and on the right is a Prirovskaya 10x1.0
General view of both tubes

If you want the replacement to take place with minimal alterations, then it is better to buy the VUT, GTZ and pedal assembly from the Priora. We dismantle the frill and remove the right half of the sound insulation of the engine compartment, the left one can simply be bent. Drain the brake fluid and unscrew the brake pipes.

In the cabin, remove the terminals from the brake light end switch and unscrew the 4 nuts securing the VUT to the body. Now you can easily remove the VUT and GTZ. If you couldn’t buy a prefabricated kit, then you need to install the pedal from the old VUT into the new one. Next, we assemble the VUT and GTZ into one unit and see that the pedal with standard mounting holes for the VUT will be rotated 90 degrees relative to the vertical position of the brake fluid reservoir.

To rotate the pedal to its normal position, you need to re-drill the mounting holes in the pedal assembly. We apply the pedal to the VUT and carefully mark where new holes need to be made. We try on and, if necessary, correct the resulting holes with a drill or file. The fastening nut is circled in red in the top photo. We screw the pedal assembly to the VUT. A few photos of the process:

VUT and GTZ and pedal assembly
Attaching the pedal to the VUT, the nut is inside, it is not easy to tighten
The other side of the pedal was much easier
VUT and GTZ assembled

We recommend: How to remove the instrument panel on a VAZ-2114 in 12 steps? Features and detailed instructions

The resulting structure is installed in the car. There was no need to cut the frill, everything was installed as original. We install the tees. We screw the Priorov tubes to the GTZ and tees. We fasten the tees to each other with a pin, preferably 5. We replace the “sorcerer” (brake force regulator) using a pit. We unscrew the brake pipes from it, remembering where they were, and remove it by unscrewing 2 bolts.

We install a new “sorcerer” instead of the old one and screw on all the pipes. We insert a screwdriver into it in advance and return to the brake pipes. We fill the brake fluid into the reservoir. To remove air from the brake system, you need to tighten the tubes in the tees not completely (leaving a gap). We blow something into the brake fluid reservoir and wait until air stops coming out of the cracks between the tubes and tees. Then we tighten it. Don't forget to bleed the brakes and adjust the sorcerer. Immediately adjust the VUT rod.

After installing the Priorovsky VUT and GTZ on a car of the tenth family, at first you will have to get used to the new brakes (much less force on the pedal is required than before), but you will quickly get used to the good ones. For the result obtained, it is desirable to have good brake discs for 14 or 15 and brake pads. By the way, you can get a similar result by modifying the standard VUT.

The process of replacing the vacuum booster on a VAZ-2110

Vacuum brake booster.

To replace a vacuum brake booster, you must have some knowledge of vehicle design. On a VAZ-2110 it is not so difficult to replace a part with your own hands.

You need to stock up on a set of tools - keys and screwdrivers and you can begin the procedure. Let's consider, step by step, the process of replacing the vacuum brake booster of the VAZ-2110:

Remove the negative terminal from the battery.
Disconnect the wire block on the brake fluid level sensor.
Disconnect the power from the brake fluid level sensor.
We hold the vacuum booster return valve and with the other hand remove the hose from it.
Unscrew the hose from the check valve.
Remove the master brake cylinder. There are only two nuts, but they can stick.
In the engine compartment, you need to unscrew the two fastening nuts of the brake master cylinder.
Without disassembling the brake, namely, without disconnecting the brake pipes, we move the master brake cylinder to the side.
We remove the cylinder with tubes from the amplifier.
From the interior side, unscrew the four nuts securing the brake pedal bracket.
We remove the vacuum booster mounts from the passenger compartment.
After this, you can dismantle the vacuum booster.
Using a screwdriver, remove the locking plate of the pin. We push out the finger and disconnect the vacuum booster pusher from the pedal.
Remove the locking plate with the finger.
Next, we are interested in the two nuts securing the amplifier to the plate, unscrew it, most likely you will have to use wd-40. We dismantle the bracket.
Read also: Where is the VIN number of the Lada Largus? Transcript, photo
After unscrewing the fasteners, remove the bracket.
Assembly is carried out in the reverse order of disassembly.

This is what the engine compartment looks like without an amplifier!

Part selection

Amplifier Torgmash.

The original catalog number of the VAZ-2110 vacuum brake booster is 21103510010.

The price of this part is 4000 rubles. In addition, there are a number of analogues that can be used. Thus, the automotive market offers the following non-original parts:

Pekar 2110-3510010 with an average cost of 2500 rubles.
Pekar 2110-3510010 is an amplifier with a sporty twist.
DK 2110-3510010 - low quality and cost around 2000 rubles.
Master-sport 2110-3510010 is an expensive but high-quality product.
Vacuum brake booster master-Sport

Symptoms of malfunction (check options)

There are several signs of a malfunction of the vacuum brake booster, and, accordingly, diagnostics of performance. Let's consider each of the options:

We start the engine and let it run for a few minutes, after which it is necessary to turn it off. Press the brake pedal several times. During normal operation of the amplifier, the pedal will be depressed the first time, but subsequent times the stroke will be less and less. If the pedal stroke does not decrease the second and subsequent times, then there is a breakdown in the system and the part is not sealed. This means that the vacuum booster needs to be replaced.
The second option assumes that the first option did not produce any results, and doubts have crept in. Depress the brake pedal and start the engine. With this turn of events, after starting the power unit, the pedal should go all the way down. If this does not happen, then there is an air leak and the amplifier does not work.
With the engine running, hold down the brake pedal and then turn off the engine. Hold the pedal for another 1.5-2 minutes without releasing it. If there are malfunctions, the pedal will rise.

The amplifier has gaskets and O-rings, and these are the ones that most often fail.

We recommend: Spark plug faults. Checking the spark plugs

Replacement and repair of vacuum brake booster VAZ 2110

In order to ensure safe movement through potholes and potholes on our roads, and in many cases to save the lives of drivers, passengers, and pedestrians, brakes were invented. And to minimize the braking distance, the VAZ 2110 has a vacuum brake booster, which also improves traction with the road surface.

Vacuum brake booster

Principle of operation

Vacuum brake booster

Signs of trouble

If the vacuum booster on a VAZ 2110 has malfunctions, they can be identified by the following signs:

When you press the brake pedal, it “responds” with a hissing sound, and the engine speed often increases;
The car “troits”;
Candles stop working;
Fuel consumption increases.

Examination

Typically, a vacuum booster is checked for serviceability as follows:

Without starting the engine, you need to press the brake several times (as when pumping);
After the 5th – 6th press, lock the pedal in the pressed position, start the engine;
As soon as the engine starts, the pedal moves forward slightly on its own. This is if the vacuum booster is working properly.

If a vacuum is not created, then the first thing you need to do is check the connections and the hose itself for leaks, as well as the check valve of the VAZ 2110 vacuum tank. Often the reason is a malfunction (ruptures, cracks) of rubber parts that require replacement.

In this case, repairs will help, namely replacing faulty parts with serviceable ones.

An internal part, such as the diaphragm, may require repair; over time, a hole may appear in it.

The diaphragm is sold as part of a repair kit. The price of the VUT VAZ 2110 repair kit fluctuates around 250-400 rubles.

Dismantling

To replace the vacuum booster, the following actions are necessary:

Remove the engine compartment trim;
Remove the trim from the windshield;
Unscrew the nuts securing the vacuum booster to the main cylinder with a 17mm wrench;
Then carefully remove the master cylinder from the studs without damaging the tubes;
Disconnect the hose from the vacuum tank;
Disconnect the wiring from the brake light switch from the passenger compartment;
Unscrew the brake pedal from the body (you will need a 13 key);
Remove the vacuum brake booster;
Disconnect the brake light button;
Using a screwdriver, pry up the locking bracket and remove the pusher pin;
Unscrew the two nuts securing the vacuum chamber to the bracket and disconnect it. Now it is possible to replace this device with a new one.

The vacuum seal is replaced in the reverse order. Then the brake light button is installed and the free play of the pedal is adjusted, which should be 3 - 5 mm.

Troubleshooting

When the identified signs indicate a malfunction of the VAZ 2110 vacuum brake booster, you can try to provide first aid to your car yourself. In normal condition, the braking system should hold it in place at an inclination of 25º to a horizontal surface. If it doesn’t cope well, you should loosen the locknut and tighten the cable.

Then you need to check the full lever stroke, it is necessary that it is approximately 2-4 teeth. After tightening the locknut tightly, it is worth performing a series of safety brakes while simultaneously monitoring the stroke of the lever. Moreover, the rotation of the wheels when the lever is lowered to the end should be free, without force. If such a test reveals the inability of the amplifier to cope with braking, this indicates the need to replace it.

Many car services provide such a relevant service today as tuning the brake system of the VAZ 2110; the price of the unit in case of replacement is still higher than its improvement. It also affects the rear brake discs, in addition to the booster, which is upgraded by installing a special washer. This seemingly insignificant detail can significantly influence the operation of the amplifier and the braking process as a whole.

When the driver presses the brake pedal, the rod passing through the washer begins to exert pressure on the brake master cylinder. Because of this, the operation of the bypass valves begins a little later. Thus, installing a washer makes braking smoother, the pedal is softer, and its reaction in case of a sudden stop does not change.

But if a hiss has already appeared, the engine stalls when the brake pedal is pressed, or it has become very tight, it is necessary to replace the mechanism. Otherwise, driving such a car becomes unsafe for yourself and others. In preparation for replacing this unit, the rear of the engine compartment must be disassembled and the elastic seal, trim and frill removed.

The process begins by disconnecting the pad wiring from the sensor indicating the brake fluid level. While supporting the check valve, disconnect the hose from the amplifier. Next, unscrew both fastening nuts of the master cylinder of the braking system. It is smoothly turned away from the amplifier to the distance required to remove the latter, and this is done without removing the brake pipes.

Under the instrument panel located in the passenger compartment, you should unscrew all four fastening nuts of the brake pedal bracket, which is quite difficult due to their inconvenient location. Then the wires, bracket and amplifier itself are removed in the engine compartment at the same time as the brake pedal assembly.

Having disconnected the two fastening nuts, use a screwdriver to remove the locking plate of the mounting pin and, pushing it out, separate the amplifier pusher from the pedal. Having unscrewed the damaged amplifier from the pedal assembly, a new one is placed in its place. Moreover, it is necessary to ensure that its location is correct: the pedal should be at the bottom and the hose fitting at the top. After this, all previously performed operations are performed in the order opposite to removal.

How to replace the vacuum brake booster on a VAZ 2110-VAZ 2112?

Removal: 1) First, unscrew all the screws that secure the soundproofing material (Most of the nuts are indicated by red arrows), then unfasten the belt securing the expansion tank of the cooling system (the tank is indicated by a blue arrow) and slightly lifting it up, remove it from the place where it is located.

We recommend: Repair of power windows on VAZ 2110

The hoses are connected to it, do not disconnect them under any circumstances, otherwise liquid will flow out, which will stain your car. Of course, you can put some kind of container and drain all the liquid from the expansion tank, but why do this if you can do without it and the work will go much faster, then carefully place the tank somewhere and fix it and then take out the left (look in the direction of the car) part of the soundproofing material and put it aside.

Note! The same thing will need to be done with the right side, in order to remove it, you first need to move the rear window washer reservoir to the side (On VAZ 2110 cars, this reservoir is not present, it is only present on the VAZ 2111 and VAZ 2112), to do this, disconnect the two wires that fit it (see photo 3), unfasten the belt that holds it (see photo 4) and carefully remove it

If there is a lot of liquid in the tank, then you don’t have to remove it, just carefully place it on the fender, but if there is none or you have pumped it all out, then disconnect all the tubes remaining from the tank and after that, remove it completely from the car and finally remove the right parts of the noise-insulating material, with a 10 mm socket wrench, unscrew the two nuts (see photo 1) and with a thin flat screwdriver, pry up the brake booster hose holder (see photo 2) and disconnect it too, and that’s it, you can take out the sound-proofing material material so that it does not interfere with the removal of the brake booster from the vehicle!

2) Now that the soundproofing material is removed, disconnect the wiring block from the brake reservoir cap (Indicated by a red arrow), then disconnect the hose from the check valve of the vacuum brake booster (Hose indicated by a green arrow) and unscrew the two nuts (Indicated by blue arrows) securing the Brake Master Cylinder to the brake booster, then carefully move the GTZ to the side, but just be careful, make sure that the brake pipes do not burst, otherwise you will have to change them.

3) After the operation has been completed, move to the salon and there unscrew the four nuts that secure the vacuum booster bracket to the body (Indicated by red arrows), and also disconnect the wire blocks (Indicated by blue arrows) from the brake light switch (Indicated by green arrow), when everything is done done, you can move again to the engine compartment of the car and, once there, pull out the vacuum booster assembly with the bracket.

4) Having placed the vacuum seal on the ground or secured it in a vice, first of all, pull out the metal stopper with small pliers (Indicated by the red arrow), then carefully knock out the rod (see small photo, it is metal and comes out very easily), pressing on it from above or vice versa from below .

5) And finally, unscrew both nuts that secure the vacuum seal to the bracket and remove it, this completes the operation of removing the brake booster.

Installation: Install a new brake booster in the reverse order of removal, during installation, do not make a mistake and do everything exactly the same as before, when it is installed, do not wear soundproofing material, but try how it works (How to check the brake booster, we have already wrote above), if everything is fine, complete the installation of all parts as they were previously.

General structure of the brake system of the VAZ 2110

The vacuum brake booster of the VAZ-2110 is located in the engine compartment of the car between the main brake cylinder and the brake pedal.

VUT layout diagram

We will briefly consider the operating principle of the vacuum brake booster in the following figure:

In the initial state, both cavities are connected to the atmosphere through a follow-up valve (not shown in the figure). When you press the brake pedal, the rod moves the diaphragm to the left, the follower valve separates the cavities and a vacuum is created in cavity “A”. And since cavity “B” is still under atmospheric pressure, both of these conditions (vacuum + atmospheric pressure) together give additional force to the braking.

You can take a detailed look at the operation of the entire braking system of a car in its entirety in the following video tutorial.