How to install a winch on a UAZ Bukhanka

UAZ 3962 “Grey” › Logbook › Installing a winch.

I bought the winch almost immediately after buying the car.
Having studied I-Net, I came to the conclusion, agreeing with many practitioners, that the power of the winch should be twice the maximum permitted weight. I have a UAZ 39625 with a title of 2720 kg * 2 = 5440. A friend recommended the store polniyprivod.ru/, where I bought a winch for 17,000 rubles. Electric Winch 12000 with wired and wireless remote control, 30 m steel cable and 3 connectors (one for the front, one for the rear of the machine and one for the winch). As I later found out, the connectors hold no more than 200A of current, and the consumption of my winch at maximum loads can briefly exceed 400A. There was a need to find the appropriate wiring. Again, many days of searching for information, formulas, etc. Again, I had to rely on the opinion of experts that for every 10A a cross-section of copper wire (core) of 1mm2 is required. Accordingly, I took welding wires of about 40 mm2. The longer the wire, the more the losses in the conductor increase; accordingly, it is necessary to increase the cross-section of the core. The standard wires were short, so I had to disassemble the solenoid block and replace the positive wire with my own. Thanks to the guys, in the workshop they crimped the terminals with a special tool, put on the casings, it turned out no worse than at the factory, but it’s just enough from the bumper through the hole in the tunnel under the speedometer cable to the battery. In the future, I want to replace the battery (battery) with a 90 Ah instead of 60, replace the generator with an appropriate one (I’m still studying the characteristics) and install a winch power cut-off relay from a button on the panel (many complained that it sometimes shorts inside and the winch rewinds without responding to the buttons of the remote control and As a result, it breaks the bumpers, platforms and its own body). Also in winter, on the advice of friends, I will shorten the cable by 10 meters. When winding too long a cable to the side, a heap accumulates at the edge of the drum, which can break the transverse fastenings of the winch if you don’t keep track. So it’s better to interchange with a short cable several times. I would like to share my development for installing a removable winch on a non-lifted UAZ 39625 (loaf, tablet) with standard bumpers. The task was unusual (I set myself the Technical Assignment), install the Electric Winch 12000 winch on a loaf without changing the appearance and without making changes to the design, so as not to register with the Technical Department, not to worry about technical inspections, not to cut the bumper, etc. Moreover, the winch must be removable and installed both front and back for all occasions. The winch platform should not be lower than the edge of the bumper. The rear footrests and standard towbar should be preserved (they are very comfortable). Centering the winch in the middle is recommended, but not required. Inspired by the idea on YouTube:

After much research on the Internet, I decided to make an American towbar: a square pipe is attached to the frame of the car, a square pipe of smaller diameter is inserted into it, welded to the platform with the winch and secured with a pin or a cotter pin. Having told the idea to the specialists (the head of the metalworking shop), they came to the conclusion that the lateral loads of the UAZ require a minimum of 2 square meters. On the Internet I found a picture with the sizes of the holes and the distances between them on the winch platform for the UAZ Patriot on the forum uazpatriot.ru/forum/viewt…pic.php?t=18614&start=210,

They coincided with the drawing in the instructions for the winch and sent it to the workshop. They did it in a week, slowly, but efficiently. The only point is that this platform should immediately be attached to the frame of the Patriot, and on my copy, on the right and left, I cut off the protruding ears with a grinder. We found a rectangular pipe, but there was no smaller diameter! We got out of the situation by taking solid pieces of metal, machined them and welded them to the site. The weight turned out to be the same! All that remains is to attach it to the frame. The hooks must first be removed. They are attached to the frame not with bolts, but with rivets, and are installed “hot”. I spent several hours sawing off the heads of each rivet with a grinder on both sides. I tried to knock it out - it was useless. I had to drill out first with a small drill, then with a large one, and only then was I able to break out the hooks. The left one also turned out to be welded to the frame along with the steering gear mounting spar - but it still broke off! What a pleasure! Next, I measured the width of the frame with a tape measure, estimated the width of the plate, and sent the drawing drawn on my knee to the workshop. Afterwards, the finished plate was attached to the frame, holes were marked on it along the holes from the hooks and again to the metalworking shop. The next time we assembled a ready-made structure.

During final assembly there were many nuances. For example, a piece of rectangular pipe used to grind squares for the winch platform turned out to be from a different batch than the pipes welded to the frame platform. It took a long and tedious time to grind off the excess with a grinder. And inside these pipes there is also a protruding seam! The metal moves slightly when welding, so the squares that had slipped on the site were straightened out with a hefty sledgehammer. In general, they created problems for themselves. When I started cutting holes in the bumper, I realized that they had climbed into the place where the crooked starter was inserted! It was necessary to move the mount by 3 cm...

At the moment, the winch is connected according to a temporary scheme; the wires are simply attached to the battery terminals with nuts. Installation is also easy in 4 minutes. The front grille is removed, a platform with a winch is inserted, it is fixed with 4 pins, which are pinned, the wires are passed to the battery through the hole for the speedometer cable, the grille is returned to its place. In the future, it is necessary to move the solenoid unit into the cabin, remove the sockets from the welding disconnectors (purchased sockets will not be suitable for the current load) in the front and rear. I will route the wiring from welding cables in a corrugated structure along the frame. As soon as I do it, I’ll post it.

Source: www.drive2.ru

Winch Master Winch E9500

Premium winch with IP68 and 2 years warranty
The top winch from the entire Master Winch line. It has IP68 moisture protection, which allows it to work even when submerged to a shallow depth. Also, reinforced gearbox gears, reinforced drum sides, a high-capacity protected contactor, a needle bearing in the gearbox, and bronze bushings bring this winch to the top of this list. And this is the only model from the entire selection that has a two-year warranty from the manufacturer.

UAZ for the hunter: Three winches for one Loaf

You can scold the loaf, you can accuse UAZ of being retrograde, but so far no one in Russia has come up with a way to replace it. For example, take a very good version of the UAZ for a hunter.

We built a car for the specific needs of a specific person and assessed the investment; Hunting takes up quite a lot of time in a customer’s life and is not the least of his interests.

Preparation and correct final product. The air intake is organized through a hole under the roof - a useful solution for fans of “swimming”.

Headlight protection is not a sham, but real steel. Well, it looks evil.

The additional canister on the gate for the spare tire increases the load on the gate, but makes very good use of the space.

In terms of mechanics, the engineers took a classic approach: a 65 mm body lift, Ironman off-road shock absorbers, pneumatic axle locks, a transfer case kit with a 3.3 lowering and higher-torque main pairs (5.2).

To install Simex Jungle Trekker tires mounted on Wheels steel wheels, the arches had to be trimmed. RIF hubs are responsible for disabling the front axle shafts.

To get into the interior of the tall car, a real retractable step was installed.

A house for talking about hunting. Or fishing. Or…

The interior of the off-road bus was divided into cargo and passenger areas.

There is no luxury ahead - only utilitarianism.

The standard front seats have been slightly adjusted to match the car's condition.

In the stowed position, the table folds up and does not get in the way.

The passenger compartment is modest, but not without a certain luxury.

Place for shmurdyak is always a sore subject for travelers by car.

The cargo-passenger version would not fit here without the need for a large trunk.

Moreover, there was room for a spacious shelf above the cargo area.

The trunk can be washed under pressure - everything is sealed and will not get into the cabin.

Special rails are installed for loading the carcass.

Runva 9500 winches are installed in the power bumpers, but in order to find the third winch, you will have to open the trunk.

A small winch for the quad is installed inside and is designed to drag the carcass of a hunted animal into it.

Electric windows made it possible to use the space for installing speakers.

In the stowed position, the canister does not extend beyond the reserve. It is almost impossible to damage it.

The final preparation of Loaf for life in the forest was completed by the Raptor protective coating.

The result was a good bus, capable of traveling along unknown paths of dense forests.

Nothing superfluous, but you will have to climb high for a shovel.

Source: www.uaz.ru

Which winch to choose for UAZ #8212 review of popular models

The electric winch on the car is an optional equipment. This is a special device for moving and lifting loads; it is used to pull out a car stuck in the mud.

In general, there are three types of winches: mechanical, manual, and electric. From this entire series it is clear that it is recommended to choose an electrically driven winch. Because on occasion there will be less work.

Today there are a huge number of such devices on the market; an inexperienced buyer may be confused about which brand of winch to choose.

It’s worth mentioning right away that the UAZ-469 is equipped with a winch with a traction force of 5 tons or more. This is the optimal tonnage for pulling a car out of an “ambush”; a winch with less force simply cannot help its owner in a difficult situation.

Complete set #171 swan#187

The additional equipment of the electric winch includes:

• the device body itself,

• cable wound on a drum,

• remote control

• travel shift lever

• cable rollers (they are called sponges)

• instructions for use

additional accessories are not included in the standard kit, so if you decide that you cannot do without a corrosion-protective sling or pulley block, purchase them separately.

Of course, there should be no dents or other visual defects.

Brands of electric winches

Popular brands include winches from the American manufacturer – WARN and RAMSEY. These winches are reliable, time-tested and strong. As a rule, they are installed on cars that constantly participate in competitions.

#171 Americans #187 have proven themselves to be excellent in difficult operating conditions; they turn the cable without any overheating of the housing and gearbox, which is especially important in harsh temporary conditions.

American winches are the most expensive on the market; on average, the price of such a unit for the UAZ-469 varies between 40-90 thousand rubles. Despite such a high price bar, WARN and RAMSEY have been operating for more than seven years, which directly confirms their quality and reliability.

The brand's electric models are manufactured in Taiwan and are a reasonable replacement for WARN and RAMSEY at an attractive price. Such winches operate in difficult conditions without breakdowns for five years, helping their owner in difficult situations.

The average cost of COME UP on the Russian market is 30-35,000 rubles, which, along with quality, plays an important role when choosing a buyer. The owners have not identified any disadvantages in using this winch; reviews about it are only positive. However, 30-40k rubles for many is an amount exceeding the limit for the purchase of #171 swan #187 and then #8212 is the next option.

Another popular and cheapest in its segment. Perhaps the most popular in Russia at the moment, because its average price is only 15,000 rubles. The winch is reliable, it is ideal for the expeditioner, the person who prefers hunting and fishing to competitions.

The only negative noted by the owners is the insufficient amount of lubricant in the gearbox. The recommendation of experts is to disassemble the winch gearbox yourself and add grease.

Recommendations for installation and operation

As a rule, installation of additional equipment should be carried out in special workshops. If this is not possible, you can install the winch on the car yourself, without the help of a specialist. Here are some tips for installing additional equipment:

• Determine the location of the winch. That is, decide where it will be installed in front or behind the car.

• Preparing the site for winches begins with selecting a piece of channel. This piece should fit perfectly into the car frame.

• We install the winch using the bolts that are included in the package. To avoid damaging the winch when tightening the bolts, place them on the corners.

• Install the winch straight, it should not be at an angle, otherwise there is a risk of breaking the unit in half when pulling the car.

• Experienced people recommend removing the standard generator and replacing it with a generator from the Bychok bus. The 90-amp Bychka generator will allow you to pull out the car without the risk of draining the battery.

• When winding the cable onto the drum, make sure that the cable lays flat, this way you will extend its service life.

• It is recommended to remove the solenoid block under the hood, or better yet, directly into the interior. Alternatively, your car will drive through puddles and creeks, and when it gets wet, the unit will close.

• When operating a winch, always throw a jacket or thick rag into the middle of the metal cable. The cable can break under load, and it’s good if there are no injuries.

That's probably all. Of course, each UAZ-469 owner will decide for himself which winch to purchase; we hope that this article will help you better navigate the world of additional equipment for the UAZ driver.

Other tire and wheel reviews:

We make a winch for a UAZ Bukhanka with our own hands

The question of how a winch is made on a UAZ Bukhanka will certainly be of interest to those owners of an all-Russian SUV who do not yet have this device installed on their car. And it can, under certain conditions, make life much easier for the owner. And for those who are constantly accustomed to traveling off-road, hunting or fishing, a winch is an absolutely irreplaceable thing. As they say, where an ordinary passenger car cannot pass, a Russian SUV will definitely get stuck! But jokes are jokes, but we have to get out. And here an ordinary winch comes to the rescue.

The winch on the UAZ Bukhanka can be installed mechanical, electric, or hydraulic. And there are also hand winches, driven by human physical force using a lever. All of these options have their pros and cons. But let's talk in more detail about each of them.

The device is connected to the shaft. The source of interaction is transmission. The winding speed is controlled by decreasing/increasing engine speed. Other advantages include high stability and traction power (achieved by motor torque). This type of winch is driven by the transfer case of the car. The main disadvantage: the winch directly depends on the serviceability of the motor; for successful operation it requires a properly running motor. If there is a problem with this node, it simply stops functioning.

This kind of device is attached to almost any car that comes with a hydraulic mechanism (UAZ included). The advantages: it works quietly and has small dimensions, powerful and has high performance. Of the minuses: its operation will be directly related to the hydraulic booster (if not, then the device will not function).

For homemade winches, as a rule, starters or generators can be used for loading. The electric winch can also operate on a dedicated electric motor installed in the car. But usually such a winch is mounted on the basis of a converted starter and must operate at sufficiently high speeds, otherwise it will not cope with a heavy machine. Therefore, some install batteries with large power reserves on their cars. Pros: high speed of operation, autonomy (can work regardless of whether the motor is on/off), simplicity of design. Of the minuses: it does not tolerate moisture well, the battery drains quickly.

Since a purchased winch, and even more so its installation, is not always available (most often due to the high cost), craftsmen have gotten used to constructing the structure with their own hands. By the way, this is quite possible to do if you have the necessary tools and certain skills. And yet, our homemade device must have a high torque, otherwise it simply cannot be used for a heavy UAZ (for example, to pull the car out of a mud hole). And most importantly, building a homemade winch will allow you to save a lot of money!

We make the structure itself using a welding machine and an angle grinder from pipes, 5 mm thick sheets of metal for the manufacture of drum discs, a chain with sprockets and a hub. All work is carried out clearly according to pre-drawn drawings. And remember the golden rule: you need to measure repeatedly before cutting.

After the winch structure itself is ready, you can install it on the UAZ Bukhanka. First, we carefully prepare the site. But first we decide: we will install the winch in front or behind. Typically, many people prefer a front location in the central part of the bumper. A channel is usually used as a platform for the device. A piece of it fits well on the car frame.

Do-it-yourself winch from a starter: instructions and video

Making such a device from a starter with your own hands is not that difficult. As mentioned earlier, the most common winches are the electric type. Below you will learn how to make it yourself from simple materials. This design is based on a car starter, preferably with a planetary gearbox.

In the attached video you can see how you can make a homemade electric winch from a starter.

Before work, you need to prepare in advance the following tools and materials:

• starter;
• welding machine;
• grinder;
• cable;
• steel sheet;
• electrical wiring;
• gearbox

The algorithm of actions looks like this:

• First you need to make a drum from pipes. They will need to have cheeks reinforced with a thickness of about 5 mm, but no more;
• make a platform from steel sheets on which all parts of the structure will be installed;
• secure the nuts, bolts, washers and drum seats on the site using a welding machine;
• We interface the gearbox with the drum, and the primary shaft of the gearbox must be directed upward. Can be used for winch plow operation;
• The starter must be interfaced with the gearbox according to special drawings and technologies. First, we install the adapter that will be needed to mount the starter at the top of the gearbox. Then the input shaft will need to be equipped with a gear that has a tooth of the required size. If all of the above steps were performed correctly, then when the starter is turned on, the gear and shaft will connect to the gearbox;
• at the end we put on a gear, which can be made from the flywheel crown. It is put on the input shaft of the gearbox.

Now you can move on to the final stage of work. At the end, you will need to fix all the nodes of our design. So, connect the electrical wiring to the starter and fix the control panel.

Do not forget to clean the mechanism from the following:

• mud;
• dust;
• oil stains;
• substances and objects that could interfere with the correct operation of the winch.

Finally, the device can be primed and then painted in one layer of paint. All this remains at your discretion. You can do without painting.