How long does it take to change the timing belt on a Priora?

September 16, 2020 Lada.Online 92 814 24

Why do LADA owners care about the frequency of replacing the timing belt (gas distribution mechanism) on their cars? Mainly due to the consequences of a broken belt, in some cases the valve bends, which ends in expensive repairs. Let's figure out at what mileage the manufacturer recommends changing the timing belt and rollers, as well as what its actual service life is.

When to change the timing belt on a Lada Priora

New timing belt from Gates

Each car has a specific procedure for replacing certain spare parts.

AvtoVAZ has installed 105 thousand km to check the condition of the timing belt.

However, there are many factors that can lead to premature wear of drive parts. And this threatens, if not the capital of the entire engine, then serious repair costs. And that's why.

Why a timing belt may require replacement ahead of schedule

The owner replaced this belt ahead of schedule, although there are practically no signs of wear on it. So calmer!

Even if the belt is slightly damaged, and this can be not only a break, but also stretching, cutting off part of the teeth, contact of the valves with the piston heads is inevitable.

The result of contact can be the most unpredictable - from bending valves to destroying crankshafts or camshafts . Some engine models are free from this danger, since if the rotation angles of the crankshaft and both camshafts are mismatched, emergency niches for the valves are provided in the piston bottom.

The timing belt can be changed “to the heap” if play in the pump is noticed

Priora, unfortunately, cannot boast of this. That is why experts on Priorov engines strongly recommend checking the condition and, if necessary, replacing the timing belt after 40-50 thousand mileage .

Checking the condition of the belt

Checking the timing mechanism

Any checks and adjustments of the drive belt are carried out only on a cold engine. Its maximum temperature should be no higher than 35 degrees.

If the car has an air conditioner, you should remove its drive belt, and only after that handle the timing belt. To remove the air conditioner belt, you need to unscrew the engine mount, and after removing the belt, install the motor on the mount, lightly tightening the screws that secure it.

Checking the timing belt is performed in the following order:

Find and unscrew the five screws securing the plastic protective cover.
Remove the cover from the engine.
Jack up the front wheel on the right.
We set the gearbox to fifth gear.
Turn the wheel clockwise.
The inner surface of the belt should not have cracks, abrasions, folds, or delamination of the rubber material.
The outer surface should be free of marks, cracks, signs of heavy wear and protruding cord.
If stains of operating materials (oil, coolant) are found on the belt, it must be replaced, but only after the causes of the leak have been eliminated.

How to check and adjust belt tension on a Priora

Timing belt in action

After inspecting the condition of the timing drive, be sure to check the belt tension and the condition of the tension and support rollers. This should be done in the following sequence:

We turn the crankshaft by the hanging wheel until the marks on the toothed pulleys of both camshafts align with the bosses on the rear drive casing.
Pay attention to the tension roller: the cutout in its cage must clearly coincide with the boss of the sleeve inside the roller.
If the belt is tensioned satisfactorily, the boss will coincide with the cutout, otherwise it is necessary to loosen the roller mounting bolt with a 15mm wrench.
To adjust the belt tension, turn the roller itself - counterclockwise to tighten, clockwise to loosen.
This can be done either with a special wrench, or a bicycle wrench of a suitable size with a grip, or pliers for removing the locking rings.
The roller is rotated until the cutout and boss coincide, after which the roller mounting bolt is tightened with a force of about 40 Nm using a 15 wrench.

When adjusting, it is important not to overtighten the belt or loosen it, since in the first case it will quickly wear out and lead to failure of the pump bearing, and in the second case, teeth may slip and the valve timing may be disrupted.

Timing belt with signs of wear

As a result, the valves can strike the piston crowns, causing serious and costly failure.

Replacing the timing belt on a Lada Priora - when to change it and should you focus on mileage?

Replacing the timing belt is carried out on DOHC engines, which are installed on Prioras, as a rule, performed after 60 thousand km. mileage Despite the fact that the manufacturer recommends changing the belt closer to 200 thousand.

There are those who don’t wait and change the belt every 40-50 thousand, but where is the truth and when should you actually replace it? Let's figure it out.

DOHC engines on Priors have four valves per cylinder (two for intake, two for intake). The valves are opened by the action of pushrods, which allows for an additional advantage when it comes to power.

Synchronization of the intake and exhaust processes is realized using a belt drive. The belt itself is a toothed, dense ring consisting of several layers of rubber and nylon. The specification and compatibility of the belt is indicated on its sidewall, in this case the width is 22 mm, the number of teeth is 137. When buying a timing belt, you should be attentive to the quality of the product; it should not have defects such as scuffing, roughness, cracks and irregularities.

The timing belt on a Priora combines many components, bending around drive rollers and pulleys. So this belt is related to the coolant pump pulley, the camshaft pulleys that lift the valves, has one guide roller, and the degree of tension is regulated by a special tension roller. To install the belt, you must follow certain rules and take into account special marks located on the belt, crankshaft pulley, oil pump, and camshafts. From the Priora factory, they receive sets of timing belts and rollers manufactured by Gates; there seem to be no questions about the belts, but the plastic rollers are considered the “Achilles heel” of these sets. Those who have had bitter experience of using such belts and rollers strongly recommend replacing them early and checking their condition regularly.

Gates belts for Priora

When entering a car store, the owner of a Priora with a 16-valve engine inevitably faces the question of which timing belt is best to choose. Among the large number of spare parts, many owners prefer GATES products.

In 2021, it celebrated the centenary anniversary of the start of V-belt production. Our research and development center allows us to produce high quality spare parts.

This was achieved:

By adding nitrile to the product material, which is a synthetic substance endowed with increased wear resistance.
The presence of fiberglass threads in the cord. They are arranged in a spiral in a rubber shell.
The products are manufactured with different tooth profiles, which ensures the girth of the pulleys and reduces noise when the motor is running.
The company's employees regularly take measures to protect their products from counterfeiting.

The company can offer buyers the following options for purchasing spare parts:

parts with normal quality;
reinforced spare parts;
The set will include rollers;
extended kit (seals, gaskets, washers, bolts).

Reviews

Stepan. Novosibirsk city. I had a choice from several companies producing belts. A friend advised me to choose GATES. I made the purchase from an auto store with good reviews from customers. The product is packaged in original packaging; counterfeit products were not found in the store. It was changed by specialists at a car service center, the mileage after replacement is already more than 30 thousand km, there are no comments.

Vladimir. Tver. The Priora's speedometer had more than 50 thousand kilometers when it decided to replace the timing belt. The old one still had clear markings from the gates company, so I decided to opt for this manufacturer. I did the replacement myself. At the same time I changed the pump and rollers. There are no complaints about the operation of the timing belt.

Alexander. Leningrad region. After my neighbor’s garage belt broke and bent the valves, I paid attention to the condition of the timing mechanism parts of my own car. I took the Priora by hand, so I didn’t know the exact mileage of the belt. The old belt was still normal. I took a kit from GATES, it has been working for the second year without problems.

Why is this so important?

I think it’s no secret to anyone what happens when the timing belt breaks, but perhaps there are those who are not in the know. In the event of a break, the synchronization of the operation of the cylinder-piston group and valves is disrupted. The pistons begin to move towards the valves, which are no longer controlled by the belt; as a result, the pistons “meet” the valves. After such a “meeting,” the pistons are destroyed, the valves are bent, and in general you end up with a major engine overhaul. Could this have been avoided? It is possible, of course, if the manufacturer of this engine thought about this at the design stage, completely eliminating such a phenomenon. By the way, there are quite a few “plug-in” engines in the world that, after a broken belt, do not need to be “overhauled”; you just need to get to a service station and replace the timing belt. In such engines, when the valve belt breaks, the valves do not meet the pistons.

The belt and rollers must be replaced immediately if, during inspection, you find:

Roughness on the belt (on the teeth or sides);
Mechanical damage;
Engine malfunctions;
Problems starting the engine;
Extraneous sounds indicating friction of the belt against the casing, rollers or pulleys.

Separately, I would like to note the appearance of vibration and black exhaust; such symptoms, of course, can occur under other circumstances, but this option should also be considered.

Consider exclusively mileage in the question: “Is it time to change the timing belt or not?” - this is mistake. Firstly, even with low mileage, problems can arise with the belt or rollers. And secondly, there are many situations when you practically or completely do not move, while the motor is running, therefore, the belt wears out. For example, if the car is used mainly in the city, the mileage may be low, but the life of the belt itself will be at its limit, since in traffic jams the engine is running, but there is practically no movement.

There are other factors that can cause a belt to fail prematurely. For example, if oil, fuel, dirt or sand gets on it. Small particles of sand eat into the surface of the belt, destroying its surface; oil and other petroleum products soften it, reducing its strength and shortening its service life.

How to independently check the serviceability of the timing belt of a Priora car: Replacing the belt

Any auto mechanic will explain to the motorist that the timing belt must be changed regularly, otherwise its rupture during operation will damage the vehicle. All motorists will be able to replace the part if they carry out the preparatory stage correctly, remove interfering components for a while, and set the timing marks on the Priora.

Experts advise checking the condition of this component of the mechanism every 105 thousand kilometers traveled. It will be useful for motorists to learn how to disassemble the mechanism and check for damage to the belt.

What is a timing belt

This is the connecting part that ensures the synchronization of two vehicle components - the camshaft and crankshaft. However, the belt not only combines these two mechanisms, it is also connected to other parts, as a result of which a huge load is placed on it.

Due to this load, it is subject to wear and therefore must be replaced after the expiration date. If you neglect the recommendations specified in the Priora instructions regarding regular replacement, the belt will break and all the mechanisms associated with it will fail.

Untimely replacement will cost the car owner too much; it is advisable to constantly check the mechanism for damage and the first signs of wear.

Experienced auto mechanics advise not to believe the statements of official dealers that the timing belt on a Priora is replaced every hundred thousand kilometers traveled. Sometimes a rupture is possible after fifty thousand kilometers, but there are cases when the mechanism has traveled more than one hundred thousand kilometers. Therefore, schedule several checks, for example every 10,000 km, to ensure that the mechanics are functioning at the proper level.

It is made of high-quality and durable rubber, smooth on top and serrated on the inside. The teeth provide the strongest grip on the gears. If, due to a long period of use, parts of the teeth fall off, the car may not even start due to the fact that the automobile oil is untimely or incorrectly supplied to the cylinders located in the engine.

A simple rubber component plays an important role in the entire mechanism of the machine. Try not to forget about checking it, because a problem detected in time will save money spent on repairs.

What should be included

When the time comes to replace the timing belt in the Lada Priora, many owners invariably face problems related to the fact that they do not know which spare parts still need to be replaced. The presence of two camshafts in the timing drive mechanism has lengthened the toothed belt, so in addition to the tension roller, a support device is also installed. The bearings of the support and tension rollers are designed for a long period of operation, but experts recommend replacing them.

Kits are available for sale that contain a toothed belt and rollers, support and guide. Often the cause of problems with the drive is the pump, which sometimes jams while the engine is running. In this case, the valves in the cylinder head and the piston are damaged. Therefore, it is advisable to purchase a replacement cooling pump, as well as antifreeze or antifreeze for topping up.

If the engine has a “solid” mileage, the camshaft and crankshaft gears will have wear, so they also need to be replaced. If they are not replaced, the teeth will be damaged. If engine oil gets into the working area of the timing mechanism drive, it is deadly, so oil seals on the shafts (distribution, crankshaft) that have lost their elasticity may need to be replaced.

When to change: consequences of untimely change

It is recommended to replace the timing belt on a Priora after different periods of time. The manufacturer claims that it can withstand one hundred thousand mileage, but experience shows that a change may be needed much earlier.

The optimal period is every fifty thousand kilometers. Some argue that over such a short service life, rubber is simply not capable of failure. However, no one takes into account the conditions - roads, fuel quality, etc.

Also, during the operation of the mechanisms, it wears out, the rubber stretches, and therefore does not provide the correct tension of the timing belt, and slippage is possible. The teeth can wear off - because of this, traction with the gears is not ensured.

There is no exact time for a change that would suit all motorists. Some take good care of their vehicles, drive carefully, and use only high-quality fuel. Others use a more extreme type of driving, foreign liquids get on the rubber, etc.

In order not to lose your car during the repair period and not to spend a fortune on restoring the mechanics, write down or remember the date of the last timing belt change on the Priora. Next, regularly check the condition of the rubber; if worn, replace it with a new device.

Signs of possible failure

There are several characteristic signs that should alert the driver:

When the engine is turned on, extraneous noise occurs. Sometimes drivers confuse a timing belt malfunction with a poorly functioning tension pulley.
If the color of the exhaust gas has changed.
The engine doesn't start well.
An unusual vibration is felt.

Pay attention to these “symptoms”, even if the Priora’s mileage with a new timing belt has not yet reached 50 thousand km. It may fail earlier if foreign liquid gets onto the drive - oil, coolant, as well as dust or dirt.

It’s worse if it’s the coolant that gets onto the drive. Firstly, this means that the gasket that ensures the pump is sealed has failed, or there is a problem with the pump. Then the rubber is damaged and service life is reduced tenfold.

Even if the belt is new, but coolant or antifreeze gets on it, it will fail even after operating for 10 thousand miles. You will have to replace the Priora timing belt and figure out why foreign substances get on it.

How to check the serviceability of the belt yourself

If you suspect that it is time to replace the Priora timing belt, it would not hurt to check the serviceability of this rubber product. Visual diagnostics will allow you to check the serviceability and absence of scuffs on the Priora timing belt.

You should have a choice of one of the tools at hand, or two at once - a 5-point hex key, or a T-30 sprocket bit. If one doesn't work, try the second.

Open and lift the hood.
You will see the front panel covering the mechanism and timing belt.
Take the key and unscrew the five bolts that hold the front panel, remove it.
In front of you you will see a mechanism, including a tension roller.
Place a jack on the passenger side and place the wheel in a suspended position. Engage fifth gear while it is working, look at the surface of the belt for damage, even small defects.
If you notice cracks of any size, mechanical cuts, or threads sticking out, be sure to replace it by contacting a specialist or yourself.
Check the pump. If any traces of coolant leakage from the pump are noticeable, then the rubber will also have to be changed, even if there is no mechanical damage.
Check the tension roller. Auto mechanics advise changing it less often than tires. The average lifespan is approximately one hundred thousand kilometers. Change it every other time you change the belt.
Measure the belt tension. To do this, press on the stretched rubber in the area between the gears of the two camshafts. You need to press with a force of about ten kilograms. Correct tension of the timing belt should not bend more than seven millimeters.
Check that the rubber is not too loose. Make sure that the Priora timing marks match the original condition. The first, similar to a recess, is located on the outer race of the tension roller. The next one is located at the base of the roller. The maximum deviation is four millimeters; if the tension does not meet the standards, the product will have to be changed.

Found a discrepancy with the standards? Change the product. A belt set with rollers for the Priora 126 engine costs only five thousand rubles. This is a much smaller amount than the cost of a major repair if a component ruptures.

Changing the belt yourself

Replacing the timing belt of a Lada Priora with 16 valves is not the most difficult procedure. Buy a kit that includes tension rollers, stock up on tools, and you’re good to go.

Instructions

Lift the hood, use a hex wrench to unscrew the five bolts on the cover, and remove it. Unscrew the two bolts from the lower timing cover.
Disconnect the crankshaft sensor.
On the passenger side, place a jack under the wheel, lift the car with it, and place the wheel in a suspended position. This will make it easier to align the marks of the mechanism and camshafts - they should be parallel, opposite each other. Combine them with fifth gear engaged, turning the wheel to the correct position. Turn off gear transmission.
Find the flywheel and remove the rubber plug with a regular screwdriver. Under the muffler you will see a flywheel with a mark, it should be located opposite the mark on the left side.
You need to get to the crankshaft pulley; to do this, remove the wheel or turn it to the right, you need to turn it all the way. Unscrew the five bolts that secure the mudguard.
Ask a friend to engage fifth gear and press the brake, at this time, using ratchet No. 17, unscrew the bolt that secures the crankshaft pulley. Rotate in the opposite direction clockwise.
Remove the thrust washer
Unscrew the bolts securing the tension and thrust rollers. Use key 15. Remove the rollers, remove the belt.
Now install new rollers, do not tighten the tensioner type, they will be used for adjustment. Reinstall the camshaft pulleys, then the crankshaft pulley.
Put on a new belt - pull it onto the crankshaft, then around the pump, then onto the camshaft pulleys.

Replacing rollers and timing belt: step-by-step steps

Initially, it should be noted that owners of a Lada Priora car with air conditioning will need to perform some steps to get to the timing mechanism. If you have a Priora with air conditioning, then initially you need:

Using a wrench with a 15mm head, unscrew the generator tensioner pulley (not to be confused with the timing belt tensioner pulley). If the roller is humming, it is also recommended to replace it.
After this, remove the alternator belt, which is also recommended to be replaced simultaneously with the timing belt drive.
Now you will have access to the protective covers of the gas distribution mechanism.

Replacing the timing belt on a Priora 16 valves with your own hands is done by performing the following steps:

Using a hexagon or T-30 bit in the shape of an asterisk, you need to unscrew 5 bolts securing the upper cover (plastic casing) and 2 bolts of the lower timing cover.
The crankshaft sensor is disconnected by disconnecting the corresponding chip near the upper timing cover.
Place a jack under the wheel on the passenger side, then lift the car and hang the wheel. This must be done in order to be able to align the marks of the camshaft pulleys. This procedure can also be performed by rotating the crankshaft pulley with a key to “17”. The photo below shows marks 1 on the mechanism body, as well as marks 2 on the camshaft pulleys. They must be combined by rotating the wheel with 5th gear engaged. If you do not plan to change the pump, then there is no need to loosen the camshaft pulleys after setting the marks.

Aligning the camshaft marks

Mark on the flywheel

Removing the crankshaft pulley

Removing the tensioner and thrust rollers

Removing the timing belt

Location of the inner timing cover bolts

We proceed to the procedure for adjusting the tension of the belt drive.

The timing of replacing the timing belt on a Priora is often unpredictable and does not always depend on mileage!

The timing belt on a Priora is a mechanical connection that controls gas distribution in an internal combustion engine. It consists of camshafts, mechanical drives to them, transmission elements such as rods, pushers, rocker arms, valves that close and open the holes in the combustion chambers, adjusting elements, valve rotation systems, belts, etc. The camshaft drive allows it to rotate with angular velocity, which is defined as half the angular velocity of the crankshaft itself. Before deciding when to change the timing belt on a Priora, it is worth familiarizing yourself with how this mechanism works and what are the features of its operation.

Belt size

The performance of the gas distribution mechanism drive on any type of internal combustion engine is important. Not only the efficiency of the engine, but also its power performance depends on this. In order for them to correspond for a long time to those declared by the manufacturers, it is necessary to carefully monitor the condition of all components and assemblies of the motor. Any Priora timing engine has a toothed belt in the drive. Its length, width, and number of teeth depend on the type of power unit installed on the machine.

You can find out which part is on the car from the car’s operating instructions, or dismantle the old one and carefully study it.

If a VAZ 2108 engine is installed, then it will have 111 working teeth with a width of 19 mm.

The VAZ 21126 engine has two camshafts in the timing belt, so the length of the drive increases. The number of teeth on such a product will already be 137, and the width will increase to 22 mm.

Features of the Priora car

Motor of the new Lada

The engine on the Priora belongs to the class of so-called DOHC engines (Double overhead camshaft), which have two shafts, each for its own row of valves (two for exhaust, two for intake). The valves are driven by pushers, which gives an advantage in power delivery.

The timing belt on a Priora car is a rubber-mechanical product with teeth along the inner edge. Its rim indicates the type of engine for which the part is suitable, as well as markings indicating the number of teeth (137) and width (22 millimeters). When purchasing a timing belt, you should check its quality by pressing on a non-toothed surface. Obvious product defects include the appearance of longitudinal or transverse cracks, delamination, and excessive roughness on the teeth.

The timing belt goes through a tensioner pulley, a timing pulley on the crankshaft, a coolant pump pulley, a pulley (toothed) for the exhaust camshaft, a pulley for the intake camshaft, and an idler pulley. The system also has marks on the crankshaft pulley, oil pump, belt cover (rear), and on both camshafts.

In the factory configuration, the car is equipped with a Gates Kit timing belt with plastic rollers, which are not of good quality, so experienced “prior mechanics” prefer to change this part even before the recommended period expires.

Features of self-checking the serviceability of the timing belt on Priora

If you are thinking about the need to replace a rubber product on a Priora, then it won’t hurt to initially check the belt drive. The inspection will reveal signs of wear and the presence of places where the product is deformed. To carry out the check, you will need to use a hex wrench set to “5” or a T-30 star-shaped bit (depending on the year of manufacture of the Priora).

The procedure for checking the belt drive is as follows:

Use a hexagon to unscrew 5 mounting bolts, with which the front upper timing drive cover is secured.

Removing the timing cover

Marks on the tensioner pulley

This is interesting! The timing belt for the VAZ-2170 on the outer rim has the following information: engine type (21126 or 21127), number of teeth - 137, as well as marking with a product width of 22 mm.

What mileage should the car have to replace the belt?

Replacing the motor belt

It is necessary to change the belt, according to AvtoVAZ itself, when the Priora has a mileage of about 200,000 kilometers, however, it is believed that during short drives around the city this element wears out faster, therefore, according to surveys, some people change it already at 40,000 kilometers, while others only at 60 thousand mileage. This part needs to be inspected every 50 thousand kilometers. The first signs that the timing belt needs to be replaced are the following:

extraneous noise when the engine is running;
difficulties when starting a Priora car;
the engine has very strong vibration (to the point of trembling throughout the entire body);
exhaust fumes are blacker than usual.

A low mileage of a car cannot always guarantee that a situation has not arisen where the belt needs to be changed. Very often, the belt drive wears out prematurely due to the fact that oil penetrates through the seals; cracks in the casing allow dirt to penetrate. These components quickly destroy the rubber of the belt, because it peels off from the cord, and dust mixed with oil gives a destructive abrasive effect. Here you need to eliminate the causes of oil leakage and visually inspect the part itself. It is believed that minor dirt can be removed with wiping paper or a rag (if there are no breaks), and it will still be a long time before it is really necessary to change the belt.

The belt must be replaced in a timely manner, without waiting for it to break, since the latter is very fraught in terms of engine repair costs (from 10-12 thousand rubles). This is due to the fact that the pistons in Priora engines do not have recesses for the valves, as was the case on the VAZ 2110, therefore, if the timing belt breaks, there is a high probability that the pistons will “meet” the valves, with the latter bending.

At high speeds, problems with the strength of the belt on the Priora can cause the pistons themselves to break and even bend the connecting rods. It would be good if there were no accidents.

Impact of mileage

The service life of drive parts depends on many factors, most often the following:

The car's mileage before replacement.
Operating conditions of the machine.
Quality of material for manufacturing.
Technical condition of timing drive mechanism parts.

Many experts and owners argue about how much mileage a car should have before replacement. No one gives a definite answer, since this can be done after 100 thousand km or more, sometimes much earlier than the recommended period. Usually, owners change the consumables of the timing mechanism after 50–60 thousand km, which many consider the best option. This figure can be changed in one direction or another. So, if the gears in the drive have wear, this will lead to accelerated failure of the belt. Its performance is greatly affected by the “age” of the product used.

When the car's mileage may be only a few thousand km, and the car has not been used for several years, in this case it is best to replace all the timing drive parts. The penetration of engine oil and other technical fluids into the drive operating area also reduces the service life of belts. The cost of timing drive consumables is significantly less than the cost of repairing the engine if the belt breaks, so you should not save on this.

READ When to change spark plugs on KIA RIO 3

Visual inspection and work procedure

How to check a belt for rupture if the car “knocks” during a trip? To do this, some car enthusiasts just need to unscrew the timing cover and visually assess the condition of the part. And this is the easiest way for the Priora series, while some foreign cars are already equipped with detectors for such a breakdown, located right in the car’s interior. It is interesting to note that both domestic and foreign cars are susceptible to belt breaks on Russian roads, often regardless of their mileage.

How to install a new timing belt on a domestic Priora car? To do this, first of all you will need:

Remove the fastening screws from the front top cover using a “5” hexagon;
Remove the mudguard from the engine compartment;
Using the socket at “17”, turn the crankshaft clockwise (by the bolt from the drive pulley leading to the generator). Inspect the timing belt for damage or contamination;
Unscrew the pair of screws that secure the lower cover from the timing drive using a hexagon to “5”;

Remove the cover and the generator drive belt;
How to avoid violation of the gas distribution order? To do this, you need to put both the crankshaft and the gas distribution shaft in the top dead center position for the compression stroke of the first cylinder (turn the crankshaft by the pulley mounting bolt clockwise until the marks on the pulleys align with the marks on the rear cover from the timing drive);
To check the position of the crankshaft, you need to remove the rubber plug located in the upper part of the clutch housing (at the same time, the coolant temperature sensors, the wiring harness from the sensors, and the cooling system hose must be disconnected). After this, it’s worth looking at how the mark is located on the “one” flywheel. It must be placed so that it is opposite the second slot on the top cover of the clutch housing on the Priora.
What action should be taken next so as not to disrupt the valve timing again when the bolt is unscrewed from the fastening on the pulley at the generator drive? In this case, you will need an assistant to fix the flywheel by placing a large-diameter slot-type screwdriver through the hole in the clutch housing and into the flywheel teeth.
Next, you need to remove the generator drive pulley, having first loosened the fastening bolt and its support washer.
Using a spanner or a 15mm socket, you need to loosen the fastening bolt from the tension roller of the belt itself (the roller turns - the tension weakens).

Return to contents

Why did it happen so?

Perhaps the automatic requests do not belong to you, but to another user accessing the network from the same IP address as you. You need to enter the characters into the form once, after which we will remember you and be able to distinguish you from other users exiting from this IP. In this case, the page with the captcha will not bother you for quite a long time.

You may have add-ons installed in your browser that can make automatic search requests. In this case, we recommend that you disable them.

It is also possible that your computer is infected with a virus program that is using it to collect information. Maybe you should check your system for viruses.

If you have any problems or would like our support team, please use the feedback form.

One of the latest developments by VAZ engineers of the last decade is the 21126 engine, which became the main power unit on the VAZ-2170.

Here, cylinder honing and new pistons were used, which contributed to an increase in power.

However, a banal break in the gas distribution mechanism drive will damage the components of even such a technologically advanced unit. Therefore, it is better to check and change this component of the system in advance.

When is it necessary to replace the timing belt on a Priora car?

In any case, the condition of the element must be monitored every 45 thousand km . The first signs that a timing belt replacement is already necessary on a Lada Priora are the following factors:

extraneous noise during engine operation;
discoloration of exhaust gases;
problems when starting the engine;
extraneous vibrations.

Low mileage does not always guarantee trouble-free operation of the car. Quite often in reviews from car enthusiasts you can come across a situation where the belt drive wears out ahead of schedule due to oil and dirt getting on it. These components enter through seals and cracks in the casing, so it is important to eliminate the causes of leaks and inspect the part.

It is important to understand that replacing the Priora timing belt must be done in a timely manner; in no case should the matter be delayed until it breaks. Otherwise, the cost of repairs may unpleasantly surprise the owner. This is largely due to the absence of recesses for the valves on the pistons, so a break in the part leads to their direct contact, after which the latter usually bend.

How to fix a plastic bumper

Problems with the strength of the belt drive at high speeds generally lead to catastrophic consequences, including breakage of the pistons and even deformation of the connecting rods. In order not to expose themselves to risk, experienced motorists are advised to periodically monitor the condition of the rubber transmission, as well as the degree of its tension.

How is a belt drive checked on a VAZ 2170?

The part is a rubber product with teeth located on its inner part. The outer rim shows:

the type of motor for which the car part is intended;
number indicating the number of teeth – 137;
marking indicating the width of the product - 22 mm.

This data will be useful to the owner who does not yet know which belt to buy for the VAZ 2170. All that remains is to prepare the necessary tool for checking:

inbus key (hexagon) to “5”;
key to “10”;
jack.

The drive status check is performed on a cold motor and consists of the following steps:

Using a hexagon, unscrew the five bolts securing the front upper cover of the timing gear drive and remove it.
Inspect the part and determine whether the Lada Priora needs to replace the timing belt . To do this, engage fifth gear, lift the right front wheel and rotate it clockwise. The product must be free of cracks, peelings and undercuts exposing the cord threads. If defects are found, the part must be replaced.
Inspect the condition of the tension roller - there should be no damage to it.
Check the belt tension by pressing a force of 10 kg on the belt between the camshaft gears and measuring its deflection - it should be no more than 5-7 mm . You can also carry out control by the position of mark 1 on the outer race of the self-tensioning roller, which ideally should be opposite the protrusion 2 . Deviations are permissible within 3-4 mm - they are adjustable, but exceeding these values means the need to replace the belt drive and rollers.

How to replace the timing belt on a Lada Priora on your own?

The process includes not only the rotation of the rubber transmission, but also the rollers - tension and support - change along with it. Repair kits are usually sold at auto dealerships. To work you will need the following tools:

head at “17”;
keys to “15”, “13”, “10”, “8”;
inbus key (hexagon) to “5”;
a special key for adjusting the roller or pliers for removing the locking ring.

Next, the process of changing the drive occurs in the following order:

Unscrew 5 bolts with a hexagon on the upper plastic casing of the gas distribution mechanism and 2 on the lower one, remove them.
Using the socket at “17”, turn the crankshaft clockwise and align both camshafts at TDC on the compression stroke of the first cylinder according to the marks. This moment is determined by aligning marks 1 on the camshaft pulleys with marks 2, which are located on the rear cover.

Remove the rubber plug in the clutch housing and check the position of the crankshaft: the marks on the flywheel and the slot on the upper housing cover must match.

Before replacing the timing belt on a Priora car , you need to remove the auxiliary drive pulley. To do this, the assistant must engage 5th gear and press the brake, and the car owner, using the “17” socket with a knob, unscrew the pulley mounting bolt and remove it.
For the convenience of subsequent assembly, before dismantling the rubber part, experienced car enthusiasts recommend fixing the camshaft pulleys with a simple wooden wedge, which should be driven between them.

Replacing brake discs on Lada Largus

Using a “15” wrench, loosen the tension roller bolt and remove the belt from the shafts. Next, remove the tension and support rollers.

Apply fixing sealant to the threads of the bolts of the new rollers. Tighten the support roller to a torque of 35-41 Nm , but do not completely tighten the tension roller. Check the position of the crankshaft using the mark on the oil pump cover.
Place the toothed rubber drive onto the crankshaft pulley. Pull both branches and put the front part on the support roller, and the back part on the pump pulley and place it behind the tension roller. If a wooden wedge was used, it must be removed.

Important! During the repair process, you need to check the condition of the coolant pump. Its shaft should rotate freely, without play or extraneous noise. Traces of coolant leakage are unacceptable. If one of the factors is present, be sure to change the pump.

How to adjust the drive tension on a VAZ 2170?

The final stage of replacing the timing belt on a Lada Priora car is performed according to the following scheme:

Use a special wrench or pliers to turn the tension roller counterclockwise.
Align cutout 1 with mark 2 on the inner roller bushing and tighten the fastening bolt to a torque of 20-15 Nm (see photo above).
Install the auxiliary drive pulley in its original place.
Turn the crankshaft 2 turns clockwise using the pulley bolt and check the alignment of the camshaft and crankshaft timing marks, as well as the belt tension. If necessary, repeat the operation.

The tension roller bolt is tightened to a torque of 35-41 Nm , and the auxiliary pulley is tightened to 105-110 Nm . Assembly is performed in the reverse order; we do not install only the upper plastic casing for visual control of the work performed.

Next, we start the engine and observe - indicators 1 and 2 on the roller should not deviate from the norm by more than 2 mm , after which they should take the working position. After checking the functionality of the units, the upper drive casing is installed in place.

The described process is similar and can be applied when repairing Lada Kalina and Lada Granta cars. The technique for replacing the gas distribution mechanism drive is available to any car enthusiast, but requires special care. The slightest displacement of the marks can result in expensive repairs.

The gas distribution mechanism ensures that the cylinders of the internal combustion engine are filled with a combustible mixture with an optimal ratio of fuel and air. The timing belt is also responsible for the release of exhaust gases in the fourth stroke of the engine.

Adjust the tension to ensure maximum mileage

Normal belt tension

What is the best way to adjust the timing belt tension? To do this, take pliers to remove the locking rings and insert the ends into the grooves from the outer race of the roller (tensioner). The belt is tensioned, while using pliers you need to turn the tension roller counterclockwise so as to align the cutout of the outer race with the protrusion of the bushing (rectangular). The roller mounting bolt is tightened with a wrench. It is worth noting that the spare timing kit does not include anything other than a belt and rollers, so all keys and sockets must be purchased separately.

How to complete the installation of this element? After installing the pulley from the generator drive, you need to rotate the crankshaft by the mounting bolt 2 turns (clockwise) and check the alignment of all marks. If there is a discrepancy, then all operations must be carried out again, because no matter how high-quality the timing belt itself is, it will not be able to perform its functions if it is poorly installed. After all the operations and reassembly of the parts, you need to start the machine and let it run for about a quarter of an hour.

Next, you need to re-check the belt tension: when a force of 100N is applied to the middle of its long part, the “sag” should be in the range of 5.5 to 6 millimeters. If you are not confident in your experience in carrying out such work, it is better to contact a car service center that specializes in Priora, so that later you do not have to pay for the repair of the entire engine. But it’s worth having basic knowledge of how to tension a belt, because this part often fails on the highway, far from service stations, even if the car has low mileage.

How to choose a belt for Priora?

In order for the gas distribution mechanism to work reliably on the 16-valve Lada Priora 21126 engine with or without air conditioning, you must choose the right product. You can purchase a factory version; according to owners’ reviews, it is considered the best for VAZ cars. Below we will analyze the types of timing belts by size, markings and prices.

Timing belt size for Priora

For Lada Priora cars, the length and overall size of the strap depends on the number of teeth installed on it. You can accurately determine which timing belt is installed in your car by identifying the engine modification and reading the user's service manual. Or you can remove the old belt and measure its size to purchase a new one.

Straps that can be used in Prioras:

with 111 teeth, the width of such products is 19 mm, installed on Prior engines from VAZ 2108;
with 137 teeth, the width of such straps is 22 mm, they are mounted on engines 21126 and have article number 137-22 HNBR.

Company and prices

The brand of the company plays an important role. When deciding which timing belt for Priora 16 cl. It’s better to choose, most consumers prefer the originals.

Below is a list of timing belts for the VAZ Priora with their cost:

The original strap is produced by AvtoVAZ, its average cost is about 1800 rubles.
The product is from the manufacturer Gates, the cost varies around 1,500 rubles. If you want to buy a complete repair kit, it will cost the buyer approximately 3,500 rubles.
Daiko, the cost of such a product is about 1,400 rubles.
On average, a Kontitek belt will cost the buyer one thousand rubles.
Products from the manufacturer Bosch have proven themselves to be positive. Their cost on average is about 1200 rubles.
One of the most budget options is the Lynx strap; it will cost the buyer approximately 700 rubles.

The “techno-056” channel provided a video that describes all the differences between original Gates timing belts and fakes.

Replacing the timing belt on a Lada Priora - when to change it and should you focus on mileage?

There are those who don’t wait and change the belt every 40-50 thousand, but where is the truth and when should you actually replace it? Let's figure it out.

Which timing belt to choose for Priora 16 valves

Which timing belt is better?

The range of different timing belts is quite wide. Depending on the brand, it differs in both price and quality. But the best belt is considered...Read More

Timing kit (belt + rollers)

Manufacturer	vendor code	price, rub.
CONTITECH	CT1137K1	2976
INA	530053610	3044
GATES	K015631XS	3478
BOSCH	1987948286	3567

Necessary tools when replacing the timing belt on Priora 1.6 16 cl

Wheel key;
Jack or lift;
Drive wrench with extensions and sockets for 10 mm, 13 mm, 15 mm and 17 mm ;
5 mm hexagon ;
Stationery proofreader;
Curved retaining ring puller (for tensioning the timing roller).

Why is this so important?

The belt and rollers must be replaced immediately if, during inspection, you find:

Roughness on the belt (on the teeth or sides);
Mechanical damage;
Engine malfunctions;
Problems starting the engine;
Extraneous sounds indicating friction of the belt against the casing, rollers or pulleys.

Separately, I would like to note the appearance of vibration and black exhaust; such symptoms, of course, can occur under other circumstances, but this option should also be considered.

Finally.

To summarize the above, I would like to give some practical advice that will allow you to avoid timing belt rupture and, as a consequence, major repairs.

Buy a quality replacement belt and rollers;
Record the mileage and date of belt replacement;
Every 10 thousand, perform a visual inspection of the rollers and belt;
Change the belt earlier if you mainly drive the car in the city;
If you buy a used car, it is better to replace the belt and rollers, since it is not known when it was changed.

That's all for me, write in the comments when you prefer to replace and how you monitor the condition of the above-mentioned elements.