No spark prior 16 valves reasons

January 15, 2015 Lada.Online 308 758 380

To start the engine, you need to ensure that a spark appears at a certain moment to ignite the air-fuel mixture in the cylinders. Problems with starting the engine occur if one or more elements of the system malfunction. The table lists possible reasons why the Priora does not start.

How to check the spark of a Priora

Good evening everyone, dear friends, today I decided to touch on a sore subject on Priora and not only, namely the failure of spark plug coils
. The Prioro engine uses individual Bosch coils, the price today is 450 g

Therefore, I suggest several ways to recognize a non-working coil (by the way, even diagnosticians at stations can’t always tell which coil is faulty and suggest the poke method)) of course, there is a device that checks the performance of the coil, but its price is about 300 USD

and not every diagnostician buys such a thing, thinking that when it will work out)

Let's start self-diagnosis, firstly, inspect the removed coil, the rubber part should be without cracks or tears (this is already a defect)

Also, the spring located inside the coil must be in the correct position

The easiest method is to wrap the coils with thermal tape.

but if this did not help, it means that some of them are definitely dead, after visually inspecting the coils with their full visual performance, we move on to auxiliary methods, namely a banal tester. Many people say that you can’t check the coil with a tester, but you can check it knowing only the initial readings) First, we check the internal resistance of the multimeter and its wires, so as not to make false measurements. To do this, set the switch to the 200 Ohm position and close the probes, mine is 0.3 Ohm

We call the primary winding of the coil; this winding is connected to pins 1 and 3 of the connector. The polarity of the connection does not affect this. The multimeter should show about 0.8 ohms

subtract its own error 0.8 - 0.3 = 0.5 Ohm - the norm. If there are no indications, then we check the quality of the connection of the probes to the coil contacts and the correctness of the connections (we need the outer terminals of the coil connector) and try to ensure better contact; if there are still no indications, then the primary winding is broken and the ICZ is faulty.

If everything is normal with the primary, check the secondary winding of the coil. To do this, move the multimeter switch to the 2000 kOhm position (or 2 MOhm), here the multimeter probes must be connected observing the polarity - red to the spring inside the rubber cap, black to the middle (2) pin of the connector. My working coil has a secondary winding resistance of 342 kOhm.

As for the 2nd coil, it is broken, to be completely sure, I removed the rubber cap, wiped it, knocked, but nothing helped - this coil is faulty and the cartoon shows infinity.

So we are not in a hurry to go to diagnosticians and give money for advice to check by replacing a new one)) first you can try your strength and intelligence)

Thank you all for your attention, good luck in life and on the drive))

The check light came on, the car started running, and after 3 km it stalled. Having opened the hood, I realized that the seal of the third cylinder had melted and leaked. I installed a new one. There is no spark in all cylinders.

Why does the engine fault light come on and the Priora jerks? – 3 answers
VAZ Priora ignition coil does not ring - 3 answers
The car suffocates in the rain, VAZ 2170 – 2 answers
Troit Priora when cold – 2 answers
I turn on the ignition, but no current goes to the starter - 1 answer

It is worth checking the fuses and ignition relays and the ECU. Is there an impulse to the injectors? If not, then the problem is with the crankshaft sensor or immobilizer. If so, then you need to check the connector and wires of the ignition coils, the ECU connector, and the problem may also be in the ECU itself.

Subscribe

to our channel in
Index.Zen
Even more useful tips in a convenient format

Many car enthusiasts have encountered the loss of spark on the 16-valve VAZ-2112 engine. What is this defect associated with? The first thing that suggests itself is the ignition. But, in this case, not everything is so simple, since the problem may lie deeper than it seems at first glance.

The video describes a situation when you lose a spark on the road and the car does not start:

Why Lada Priora does not start, causes of malfunctions

If the Lada Priora's starter does not turn

Possible malfunction Diagnostics Remedies

Low battery	The voltage at the battery terminals without load is less than 12V. When trying to start the engine, a cracking noise is heard from under the hood.	Charge the battery or replace it with a new one
Oxidation of battery terminals or wire terminals, their fit is not tight	When you try to start the car, the voltage in the on-board network drops much more than at the battery terminals. In this case, a crash may be heard under the hood.	Clean the contacts, lubricate them with petroleum jelly and tighten the terminals
The engine or attachments are jammed	Check the rotation of the crankshaft, pump and generator pulley.	Repair engine, generator, pump
The starter is faulty, the starter drive gear or flywheel ring teeth are damaged	Remove and inspect the starter.	Repair or replace starter
The starter switching circuit or starter relay is faulty, the wires are damaged, or the ignition switch contacts do not close	When the key is turned to position “II”, the starter traction relay does not operate (a click is not heard under the hood). Check the +12V supply to the control contact of the traction relay.	Replace starter relay, wires, ignition switch
The starter traction relay is faulty, there is a short circuit or break in the retractor winding, the relay armature is stuck	When the key is turned to position “II”, the traction relay does not operate (there is no click under the hood), but + 12V is supplied to the control contact of the traction relay. Remove the relay and check its operation.	Replace the traction relay
Contacts or wires of the traction relay are oxidized, poor ground contact	When the starter is turned on, a clicking sound is heard under the hood, but the starter armature does not rotate. Using an ohmmeter, check the resistance of the Battery-Starter circuit, as well as the ground wire. If the circuit is in good condition, remove the starter and check the operation of the traction relay by applying +12V to it from the battery	Tighten the terminals, clean the contacts, replace the traction relay
Open or short circuit in the holding winding of the traction relay	When you try to start the engine, you hear a crashing sound under the hood. The battery voltage is within normal limits. We check the traction relay with an ohmmeter or by its excessive heating.	Replace the traction relay
Burning of the starter commutator, sticking of the brushes or their severe wear; Break or short circuit in the starter armature winding	The starter armature rotates slowly or does not rotate at all. Check the traction relay by applying voltage to the starter contact bolt directly from the battery	Replace starter or armature
Freewheel slipping	When the starter is turned on, the armature rotates, the flywheel is stationary	Replace clutch or starter

Priora won't start, starter turns

Possible malfunction Diagnostics Remedies

There is no gasoline in the tank	On the instrument panel the fuel level indicator is at zero.	Pour gasoline
Battery is low	The voltage at the battery terminals without load is less than 12V. When trying to start the car, a crashing sound is heard from under the hood.	Charge the battery or replace it with a new one
Oxidation of battery terminals or wire terminals, their fit is not tight	When you try to start the engine, the voltage in the on-board network drops much more than at the battery terminals. In this case, a crash may be heard under the hood.	Clean the contacts, lubricate them with petroleum jelly and tighten the terminals
Unreliable connection of electrical circuits of engine control and power supply systems	Check the connections of the connectors and the reliability of the contacts in the blocks.	Fix faulty wire connections
Increased resistance to rotation of the crankshaft (scores on the shafts, bearing shells, cylinder-piston parts, deformation of the shafts, frozen engine oil, jammed generator, jammed coolant pump)	The crankshaft turns slowly. If the engine is started in severe frost, and the engine was working properly the day before, then most likely the engine oil has frozen. If you hear extraneous noise when starting the engine, check the free rotation of the pump and generator pulleys.	Use the recommended engine oil. Repair the engine. Replace the pump and generator.
Malfunction in the ignition system	Check for spark.	Check the circuits and devices of the ignition system. Replace faulty system elements.
The high voltage wires are connected in the wrong order or the wire is disconnected	Inspect.	Connect the wires in the correct order
The timing belt is broken or the belt teeth are cut off	Open the front timing cover and check.	Replace timing belt
Disturbed valve timing	Check the marks on the crankshaft and camshaft pulleys.	Set the correct shaft position
Malfunction of the computer (brains), its circuits, crankshaft position sensor or coolant temperature	Check the supply of +12V to the ECU, the sensor circuit, and the absence of damage to the sensors themselves.	Replace ECU, sensors.
The idle air regulator (IAC) or its circuits are faulty	Check the idle air control. When starting the engine, lightly press the gas pedal. If the engine starts and stalls when you release the gas pedal, the sensor is faulty.	Replace sensor
The fuse is blown or the main relay of the control system is faulty	Check fuse and relay.	Eliminate the cause of the blown fuse. Replace fuse and relay
Fuse blown, fuel pump relay. Circuit, relay or pump is faulty.	When the ignition is turned on, there is no sound of the pump running. Check the fuse. Apply voltage to the pump from the battery.	Clean contacts, replace faulty circuits, replace fuse, pump and relay.
The fuel filter is dirty, the water in the fuel line is frozen, the fuel line is damaged	Check the pressure in the fuel rail and the condition of the fuel lines.	Replace the filter, blow out or replace the fuel lines.
Insufficient pressure in the fuel rail	Check the pressure in the fuel rail, the pump strainer and the condition of the fuel lines.	Clean the filter. Replace pump, fuel pressure regulator
Faulty injectors or their power supply circuits	Check the injector windings with an ohmmeter. Check the chains for breaks.	Replace injectors, replace chains
Air leak into the intake tract	Inspect the joints and fittings of the hoses and clamps. During start-up, turn off the vacuum brake booster and plug the receiver fitting.	Eliminate air leaks, replace vacuum booster

Reasons why Priora starts and stalls

Ignition coil electrical connections are loose or damaged.
Insufficient pressure in the fuel rail.
The connections of the intake tract parts are leaking (catalytic manifold or intake manifold receiver).
The engine control system is faulty. Run diagnostics.

Lada Priora does not start when cold

If the crankshaft rotates slowly, the battery may be discharged or the engine oil may be frozen.
The vehicle's fuel system is faulty. The water in the ramp may have frozen.
The coolant temperature sensor (DTOZH) of the engine management system is faulty.
Fuel injectors are leaking.
Low compression in cylinders.
The engine control system is faulty. Run diagnostics.

If the Lada Priora does not start well when cold

Pay attention to the quality of the fuel; there may be a lot of water accumulated in the gasoline.
Check the ignition module, as well as the serviceability of high-voltage wires and spark plugs.
Check the oxygen sensor.

If the Priora does not start well when hot

In this case, see the second table; in addition to the reasons described, also pay attention to:

A pressure regulator that can discharge fuel through a membrane into the receiver.
DPKV contacts, if the sensor has been changed, check that the poles are connected correctly.
Faulty ignition module.

Let us remind you that in some cases the Priora does not start due to a faulty immobilizer or alarm system. In some cases, reflashing the engine ECU (electronic control unit) helps solve the problem of poor starting. And regular car maintenance will help eliminate problems of poor engine starting. Keywords: Lada Priora engine | ignition system for Lada Priora | starter Lada Priora | power supply system for Lada Priora | ECM Lada Priora 14 1 Found an error? Select it and press Ctrl+Enter..

Source: https://lada.online/do-my-self/repair/repair-lada-priora/217-pochemu-ne-zavoditsya-lada-priora-prichiny-neispravnostey.html

No spark prior 16 valves reasons

Welcome to ChipTuner Forum.

Theme Options

The 2nd cylinder on the Priora does not work. Prehistory. Recently I became the owner of a VAZ 2170 16v with a mileage of 90t.km. I began to notice that in the mornings the car did not start the first time, it was idling, then warmed up and after 30-50 seconds, everything was normal, it also squeezed out oil due to crankcase gases. I have made a trail. work: 1. Cleaned the ventilation system. crankcase 2. changed the O-rings on the intake receiver 3. cleaned the throttle valve (along the way for the sake of prevention) 4. changed the NGK spark plugs 5. cleaned all the injectors, measured the resistance - 12.5 ohms on each 6. voltage to the injectors - 8 V, 7 .voltage on the coils is normal 12V. 8. I pulled out the coil from the spark plugs, turned it with the starter - there was a spark. After that the car did not start, I left it overnight, it sat and started, but the problems did not go away. In the cold, the same thing happened. According to diagnostics - misfire in the 2nd cylinder.

Next I decided to flash the ECU 7.9.7. I resoldered the 6.8k Ohm resistor - it didn’t connect, soldered the eprom and 81 contacts on the computer, closed the box and calmed down - I couldn’t fix it, put it in the car, started it - now it’s constantly running both cold and hot. ((.

Maybe because of the ecu. I heard that if the key is broken, one of the cylinders may fail. but there is a spark, there is voltage on the coil and injector. It will not be possible to install a block from another car, because... My unit is somehow connected to the system via an immobilizer. At least I tried to install January 7.2 - it is not diagnosed.

There are still a couple of ideas left in my head, I need to finish them off: 1. Check the timing marks 2. Hydraulic compressors

HELP ME PLEASE! Perhaps it’s my own fault, I need to climb into the car less, I’ll drive more, I’ve learned it, but I need to finish the job. If it doesn't work, I'll go for diagnostics.

Help, I’ve broken my head, the spark has disappeared on my 16-valve Priora, and the car won’t start, fuel is flowing, the computer has been checked - everything is fine, the crankshaft sensor is also intact, but still there is no spark. I have already changed the modules and spark plugs, it started for me once, but the revs did not rise. Now it won’t start at all. There is no spark on the 16 valve Priora.

no spark in cylinders 2 and 4

Megatheronosaurus

Group: Users
Posts: 6,805

nineman

Group: Users
Posts: 155

Megatheronosaurus

Group: Users
Posts: 6,805

I saw how the controller works on a Zhiguli car. I believe in any miracles.

They brought me the controller already removed, we disassembled it with a torx screwdriver and saw what the problem was.

nineman

Group: Users
Posts: 155

Megatheronosaurus

Group: Users
Posts: 6,805

nineman

Group: Users
Posts: 155

Well, the controller was removed from the working car, I started it myself, turned it off, removed the controller and put it on mine, I started it and two cylinders did not work.

IKZ device

The Priora coil consists of a primary and secondary winding, between which a core is placed. To contact the spark plug, a spring is used, which is placed in a rubber tip. The IKZ also has a metal screen that protects the coil from high temperatures, because IKZ is installed in the well of the cylinder head, then the temperature conditions there are simply enormous.

The primary winding is wound from thin copper wire with a number of turns of 10,000-15,000.

The secondary winding of the coil consists of 100-150 turns of thick copper wire.

The connection between the coils is electromagnetic.

Why do IKZ coils burn on a Priora?

Our life development2 months ago

@Alexander 1985 If you regularly clean the spark plugs, check the gap, and resistance, they become one of the most unkillable elements. If you never unscrew them and drive on bad fuel, then the car gradually stops moving and the body is pierced and the contacts begin to burn out and the spark hits anywhere, but not in the central part. Then you throw out the spark plugs and maybe the coils. It’s not just that a spark plug starts to work incorrectly; if you correct the cause at an early stage, you’ll save the spark plug. They have only 4 simple parameters that can be checked without problems (Resistance, body integrity, contact part and just cleanliness). Until the gas begins to break through and changes the resistance of the resistor to critical values, the spark plug can work. The contact electrode does not simply burn out either. And what kind of spark there will be depends on the quality of the spark plug. I also have candles from the USSR, I cleaned them, calcined them, soaked them in dimexide, they became like new and work better than many newly purchased candles, and these are candles that were lying around in a barn under a layer of dirt and rust. All the parameters of the spark plugs indicate their serviceability, although I don’t know how old they are, how long they were used and what they were used for. With our fuel, it’s stupid to service them and not run into crap from shit and sticks. I drive with 2 sets of spark plugs, each spark plug has a high-voltage resistance wire matched to it, the difference in circuit resistance from the lowest to the highest is 0.6 K ohms. Every year I remove one set and install another, put the removed spark plugs and wires in order and they wait in the wings. The condition is excellent, not a single spark plug has failed yet and there is no wear on the contact part. Some NGK spark plugs lasted about 40,000+, the second Finwhale - 50,000+ km with me and I don’t know how long the previous owner had them. For the sake of the experiment, I installed a wire with a resistance twice as high on cylinder 4; as a result, even visually this spark plug is 2-3 times thicker in carbon deposits. The remaining spark plugs and wires were brought to balance in terms of resistance and the carbon deposits on them are minimal and absolutely the same. Lately, acceleration has gotten worse and the valves are clicking louder on one cylinder. Yes, I get very confused and there will be those who will say that the difference in resistance between the cylinders of 10 Kohm does not matter for high voltage, but only with the selected resistance the engine pulls and runs softer and the valves begin to click equally quietly, according to the theory now the working conditions of all The spark plugs and coils are as identical as possible, the spark strength is the same everywhere, although I had to select wires from 3 different sets. Through experiments, I was convinced that the spark plug that has the greatest resistance works worse and cleans itself much worse. For skeptics, the engine is in good working order, carbon deposits and its color indicate normal operation of the spark plugs and the engine, the piston is in order, the valves are adjusted and the technical condition of the engine is 4+, there are no malfunctions. As for the video, because of the spring it may work worse due to oxidation, but this is unlikely to be the only problem and the reasons for combustion need to be looked deeper.

( 1 rating, average 4 out of 5 )

conclusions

Loss of spark on a 16-valve VAZ-2112 may be a consequence of the failure of several vehicle components at once or each individually. But, if the operations indicated in the article did not help, then you should contact specialists at a car service center who will accurately identify the cause and eliminate it.

It is unlikely that several nodes will fail at once. This has not happened in my practice. Unless, of course, you hit the car properly.

The ignition coil rarely fails because it is initially reliable. But the spark plugs and fuel pump often fail.

Even if the timing phase is off, there should be a spark!

There will be a spark, but not at the right time when the air-fuel mixture arrives.

the article sucks. wrote the teapot. Moreover, the pump and the spark, and the timing belt. even with a broken timing belt there will be a spark. Kettle...boil somewhere else

What does the fuel pump and broken phases have to do with it? The author is in the furnace.

Wrote 100% who themselves have no idea what they are writing, if on the 12th engine if the spark disappears completely, then 80% is the module, and then 5% each of the crankshaft sensor, ignition switch, ECU and a break in the bus from the brain to the module or crankshaft all

Oh yes, I almost forgot the immobilizer and the signaling may be glitchy

The spark disappeared on the 16-valve VAZ-2112 injector: causes and diagnostics

The video describes a situation when you lose a spark on the road and the car does not start:

The main reasons for the lack of spark

General view of the engine 10-12 series 16 valves

Not all motorists know the reasons for the loss of spark, much less methods for diagnosing and troubleshooting problems. So, it is worth identifying the main reasons, and then deciphering why exactly they become the cause. Finally, you need to consider ways to eliminate the defect. So, what reasons could cause the spark to disappear:

Failure of the fuel pump.
Spark plug.
Ignition coil.
High-voltage wires and their location.
Gas distribution mechanism.

All the reasons have been found and it is worth moving on to the process of eliminating this malfunction.

Are you giving me a spark? Troubleshooting!

First of all, it’s worth noting that you don’t need to rush to check right away. As practice shows, there is a certain sequence of actions and malfunctions that could lead to loss of spark on a 16-valve engine.

Fuel pump

Fuel pump made by Bosch

Ignition is not the first reason for the ignition failure on a car. Before getting into the electrical part of the car, it’s worth delving into the mechanics, so to speak. Turn on the ignition and listen to see if the gasoline pump is working . If it is silent, then you need to check whether gasoline is entering the cylinders.

It is worth starting the diagnostic procedure by checking the fuses for serviceability. Of course, you can only view the one that is responsible for the fuel pump (in this case, when you turn on the ignition, the pump will not pump), but it is recommended to diagnose everything for integrity. If at least one fails, it must be replaced.

The fuses are located to the left of the steering wheel under the light mode switch

If the previous procedure did not help, then we turn directly to the pump itself. For diagnostics, you will have to remove the entire module, which is located under the rear sofa, and disassemble it.

The pump itself is easy to check - the contacts are closed through the tester. If there are no readings, then the part has “died” and requires replacement. If the pump is “live”, then it is necessary to clean the contact group and check the wiring for breaks.

Spark plug

Location of spark plugs on the engine

The candle becomes the second boundary, which may cause the spark to disappear. We unscrew the elements and carry out visual diagnostics. If everything is clean and beautiful outside, then you need to measure the resistance and check the gap. Of course, you can check the performance of a spark plug on a special spark plug stand, but not everyone has one in their garage. Therefore, we do everything the old fashioned way.

We connect the spark plug to a high-voltage wire, which is connected to 1 cylinder, and with the outer side to the body to obtain ground, and provide an ignition contact.

When performing this operation, you should be extremely careful, since the voltage that enters the spark can be fatal. Thus, we check all the spark plugs for the presence of a spark.

An alternative way to check spark plugs

Checking the spark plug using a piezo element from a conventional lighter

The 16-valve VAZ-2110 has no spark

Obvious reasons include malfunctions of the ignition coil, spark plugs, fuel pump, high-voltage wires and gas distribution mechanism.
Troubleshooting is carried out similarly to an 8-valve car. Candles are the first stage of testing. A visual inspection will help find flaws, after which they resort to checking the gaps and measuring the resistance.

Proven method: unscrew the spark plug, put on a high-voltage wire, install the base on the engine or body. After cranking the starter, a spark should form. Safety regulations must be followed.

Another reason may be hidden in the timing belt, namely, if the valve timing has gone astray due to improper installation of the timing disk. It is located on the crankshaft pulley and acts as a synchronizer.

It is quite possible to correct the situation if you change the installation of disks in accordance with the applied marks. The easiest way to find shortcomings is in working with high-voltage wires. However, it is necessary to understand that the engine will operate in strong vibration mode.

What could be the reason:

The wire doesn't work. A complete replacement helps.
Incorrect connection. Change the connection location.

There is no spark, we check the functionality of the components. Algorithm for finding a spark on spark plugs and ignition coil

When the spark is lost, you will, of course, never start the car, and in such a situation, first of all, you need to check the ignition system.

The vehicle's ignition system plays a key role in its operation. If in case of many other malfunctions the car can be taken under its own power to the service station, then in case of problems with the ignition it is unlikely that it will be possible to start the engine at all.

How to check the spark

Checking the spark on a spark plug can be done in several ways:

Check for ground (the spark plug body is pressed against the engine and the spark is analyzed when the starter rotates).
Checking the spark plug with a multimeter (you can determine the breakdown of the spark plug).
Diagnostics with a tester based on a piezoelectric element (the testing principle is similar to the ground breakdown method; the presence of a spark is determined and is used mainly on fuel-injected cars).

The main reasons why there is no spark

problem with spark plugs (flooded or faulty);
breakdown of high-voltage wires or loss of contact;
the reason is the crankshaft sensor (requires checking with a multimeter);
malfunction in the ignition module;
failure of the ignition coil;
problem in the switch;
Distributor malfunction (burned contacts, loss of clearance);
poor ground wire contact;
failure or malfunction of the ECU;

No spark injector

You need to be very careful when checking the spark on fuel-injected cars (especially for foreign cars - you can burn the electronic unit).

It is recommended to use a spark gap to understand at what stage there is no spark on the spark plugs (no spark from the distributor, no spark from the coil, or directly from the spark plug itself). If there is no spark in all cylinders at the same time, there may be several culprits:

controller;
entire module;
coil or center wire.

The entire checking procedure should begin with the integrity of the fuses, the condition of the ground contacts and contacts on high-voltage wires.

If there is no spark from the ignition coil, then the reason may be hidden in many places. First of all, you need to check the high voltage wire, which must be in perfect condition and without damage to the insulation. Otherwise, the wire needs to be replaced.

No spark, check spark plugs

If the problem is not solved, then check the spark plugs. The spark plug contacts must be clean. The fact that there is no spark may be caused by dirty spark plug contacts. It is best to replace the spark plugs, but you can also clean the contacts. But before changing the spark plugs, check whether the discharge reaches the spark plugs themselves.

To do this, remove the spark plug wire and bring it to the car body at a distance of 0.5 cm. Turn the starter several times and see if there is a spark between the wire and the body. The spark should be white with a slight blue tint.

If it is absent or present, but with a different shade, we can say that the spark plugs are fine, and the problem is in the heart of the car’s ignition system - the coil.

How to check spark on ignition coil

To see if the coil is working at all, pull the wire from the breaker distributor that comes from the coil. The same test is carried out with it as with the spark plug wires, namely, they bring the wire to a distance of 0.5 cm and turn the starter. Now, regardless of the result, we can accurately talk about the cause of the breakdown.

If there is a spark, then the problem is in the distributor-chopper; if there is no spark, then the ignition coil is faulty.

In the first case, you need to check the contacts in the distributor-breaker for oxidation, insulation damage, and also check the serviceability of the rotor. If there is no spark due to it, the rotor must be replaced.

Checking the ignition coil

Checking the ignition coil also involves inspecting the integrity of the windings for physical damage, as well as burnt spots, which indicate a short circuit in the coil. In these cases, the coil either needs to be repaired or replaced.

If, after checking, you realize that there is a spark in the car, but it does not start, then the ignition switch may need to be replaced.

to our channel in Yandex.Zen

Even more useful tips in a convenient format

If, as a result of the check, it became clear that the spark hits the spark plugs, but the VAZ 2110 injector engine still does not start, then it is also necessary to diagnose it. The faults that cause this problem can be serious or not very serious.

At the same time, it is sometimes possible to cope with their solution without anyone’s help:

It is necessary to purchase a spark gap and a Hall Sensor, which is inexpensive, but has an irreplaceable purpose. With their help, you can find out about the presence of a spark in the candles;
Check the spark plugs to see if they are OK. A spark gap can be used for this purpose. However, you need to remember that the controller will be broken if candles are placed on its body;
Perform fuel pump diagnostics. When you try to start a VAZ 2110 car, a characteristic sound will appear from under the rear seat. If there is no sound, then you need to check the fuses and the main relay. In a VAZ 2110 car they are located behind the side cover of the driver's seat.

No spark VAZ (injector, 8 valves)

The other day, out of the blue, the car (Kalina 1.6, 8 valves) began to shake terribly. Diagnostics showed misfires in cylinders 1 and 4. After a little checking (see how to check correctly here), I came to the conclusion that there was no spark . And only in cylinders 1-4.

Next, in order to find out the reason for the loss of spark, I will go in order.

The first thing to check is the spark plugs. The spark plug looked normal, so I didn’t have much hope that replacing it would fix the situation. And so it happened - the new spark plug still refused to produce a spark.

The second is checking high-voltage wires. They are checked with a conventional multimeter in resistance measurement mode. The resistance should be within 15 kOhm. The wires also turned out to be fine.

Third, and probably most important, is the ignition coil. She, like no one else, is responsible for the spark. Its operability is also checked with a multimeter in continuity and resistance measurement mode. First you need to check the resistance between pins 1-4 and 2-3. It should be about 4 kOhm. If the tester shows infinity, then the coil is broken and must be completely replaced. Next, check the resistance between pins 1a and 1b. There shouldn't be a break here. And the last thing is to check the central contact for breakdown to the housing. The tester should show infinity.

My reel passed the test perfectly. It seems that all the main parts are working properly, so why is there no spark? After digging a little on the Internet, I realized that I still need to check the circuit from the ECU to the coil itself.

A 3-pin chip is placed on the ignition coil, therefore you need to check these 3 wires. The central contact is +12V, which is constantly supplied when the ignition is on. The extreme contacts - 1a and 1b - provide a control signal (negative) at the moment when a spark is needed. How can all this be checked? Very simple - using a regular light bulb.

You need a lamp with a power of 1-2 W or an LED with an additional resistance of 500-700 Ohms.

We connect the lamp to the central terminal and contact 1a and ask a partner to crank the engine a little (first remove the fuel pump fuse and relieve the pressure in the rail). When cranking the starter, the lamp should flash. The same procedure must be done with pin 1b - the lamp should also blink.

When I turned on the ignition, the lamp started to light up, just constantly on (pin 1b and central). This means that the control wire has a short to ground somewhere or that the transistor (VT1) in the ECU is broken. To find out, we need to find the ECU, disconnect the wiring harness from it, find the wires we need (1b) and test them for integrity.

Having found the contact diagram, I found out that contact 1b goes to pin 5 of the ECU, 1a goes to pin 2, 3 goes to ground of the ignition circuit. I rang them for integrity - they were all intact. I called ground and everything is fine too. Therefore, you need to check the transistor in the controller itself.

My car has a January 7.2 controller. Inside there are 2 transistors that pass control signals to pins 1a and 1b of the ignition coil. So one of these transistors was broken, i.e. was constantly in the open position.

How to check the transistor for serviceability? It has 3 pins - 2 of which are soldered. It is necessary to ring each outer terminal with the central one. In both cases, the tester should not beep. The contacts must not be closed.

Now all that’s left to do is to unsolder the broken transistor (its marking is gb10nb37lz), solder a new one in its place and rejoice at the spark that appears.

Possible errors in VAZ injectors

Codes can indicate malfunctions of any parts and components in the car. Most often this is due to sensors. Temperature sensors are especially affected - they overheat. Car enthusiasts also complain about the injectors. Problems arise due to breaks in the circuit. As a result, they cannot respond on time. This also includes a popular breakdown on the VAZ-2110 - no spark. The 8 valve injector cannot start normally because of this.

Now about engine-related errors. The most common one is overheating. The spark plugs also overheat, causing the spark to disappear. As a result, the motor does not show any signs of life. Next we should consider the valves. These parts may become too dirty, causing them to close completely.

If the Priora does not start well when hot

In this case, see the second table; in addition to the reasons described, also pay attention to:

A pressure regulator that can discharge fuel through a membrane into the receiver.
DPKV contacts, if the sensor has been changed, check that the poles are connected correctly.
Faulty ignition module.

Keywords: Lada Priora engine | ignition system for Lada Priora | starter Lada Priora | power supply system for Lada Priora | ECM Lada Priora

+14

Share on social networks:

Found an error? Select it and press Ctrl+Enter..

Possible reasons for absence

Most modern cars are equipped with many sensors. They make the life of the car owner easier and complicate repairs. In the electronics responsible for the operation of an injection engine, there are several sensors responsible for the spark formation process. But the reasons that there is no spark (VAZ-2110, injector, 8 valves) may also lie in other components. There are several types of possible breakdowns. The first includes various problems in the car’s fuel system. This includes malfunctions in which fuel cannot enter the cylinders or the supply is interrupted.

If there is no spark (VAZ-2110, injector, 8 valves), then this may be due to the fuel system. Often the pump relay or the submersible element itself fails. The test is performed by ear.

Then there are problems related to the electrical part. These are some of the most common faults. In case of such breakdowns, no electric discharge reaches the spark plug. Naturally, the mixture will not be set on fire. Global problems include complete engine failure and timing belt breakage. It is not worth dwelling on these malfunctions in detail.

Errors during diagnostics

Most car owners, due to ignorance of the VAZ 2112 injector structure, often make mistakes in the process of identifying problems. Let's look at some of them:

Seeing that there is no spark, the “masters” want to check it for breaks. For this purpose, they place the wire close to the ground of the machine. But when performing such actions, the ignition module may break, so under no circumstances should you do this;
Errors when checking spark discharge. If you place spark plugs on the engine body, a large induction current may appear. This occurs even due to slight contact of the spark plug with the ground, as a result of which the controller can also be damaged. Therefore, it is necessary to use a spark gap that will not allow the distribution of ignition with the same supply of high voltage to two spark plugs at once.

Possible reasons why there is no charging in the VAZ 2110 injector

Many of these cars have various sensors and components. These additional devices make repairs much more expensive. The electronic injector is equipped with several sensors, malfunctions of which lead to the spark disappearing.

In addition, the following types of breakdowns are possible:

Malfunctions in the fuel supply system.
Electronics faults. A fairly common type of breakdown in which there is no spark in the VAZ-2110. The spark plugs do not receive an electrical impulse and the fuel mixture does not ignite.
Global damage associated with engine failure, bent valves, broken timing belt. Such breakdowns require complex repairs.

The lack of a spark may also be due to a breakdown of the fuel pump relay or this part as a whole. If you insert the key into the ignition switch, turn it and the sound characteristic of the pump does not appear, then the following options are possible: the relay does not function, the wiring is broken, the fuel pump is broken.

You can also check the pump in another way. For this you will need a pressure gauge. It is connected to the fuel supply system and the indicators are measured. If the figure is 2.5 atmospheres, then there is not enough pressure.

Missing spark

INJECTION DIAGNOSTICS

So, the engine won't start? In previous conversations, we figured out how to check the electrical circuits of the fuel pump and injectors. Well, what to do if the control signal does not arrive at them? Let's start “from the stove” - the master disk. This is a gear wheel combined with a generator drive pulley (2 in photo 1). If it turns (for example, a rubber damper has peeled off), the engine will not be able to start. Perhaps you will use the experience of those who talked about this in ZR, 2003, No. 4. Otherwise, you need a new pulley.

Let's assume that the pulley with the toothed disk is in order. Then let's move on to the electrical part. If there is no spark at the same time at the spark plug and a signal at the injector, then with a high degree of probability the crankshaft position sensor (DPKV - 1 in photo 1) or its circuit is to blame. Not receiving a signal from this sensor, the controller regards the situation as an engine stop and interrupts control of the injectors and the ignition module.

To check the performance of the DPKV, remove the high-voltage wire from the spark plug of any cylinder, insert a working spark plug into the tip (possibly from a spare one) and, placing it on ground, turn on the starter. Is there a spark and signal at the injector? This means that the DPKV and its circuit are working properly and the spark plugs may need to be replaced. During this check, a reliable connection of the spark plug body to ground is extremely important, otherwise the high voltage will break through the insulation of the secondary winding of the ignition module and that will be the end of it. And for a new one you will pay about 1,500 rubles. If you do this together, then you must press the spark plug body tightly against the “ground” (for example, a valve cover), after which your assistant will turn the ignition key. And not vice versa. If you work alone, the spark plug must be secured so that the spark can be seen even from the driver’s seat. We show one of the options for fixing the spark plug in photo 2: a wire connects its threaded part to ground.

...What if there is no spark? Then we’ll check the DPKV itself. Its signal is an alternating voltage, which when cranked by the starter is about 4.5 V. How can you verify this? It is best to use a simple device - a DPKV connector with two wires.

Having disconnected the harness block from the DPKV, replace it with a connector with wires, connect a multimeter to them, switch it to the AC voltage measurement mode and turn on the starter. No signal? The sensor is at fault. Is the AC voltage around 4.5V? The sensor is ok. But perhaps its circuit is faulty. In this case, let’s check the signal coming from the DPKV to the controller contacts (diagram 1).

Having removed the negative terminal from the battery, disconnect the harness block from the controller, connect a multimeter to pins 48 and 49 of the harness block, then restore the connection between the battery and ground and crank the crankshaft with the starter. The voltage is normal, which means there is a defect in the controller itself. No signal - the sensor circuit is damaged.

It is possible that a signal is sent to the injector, but there is no spark at the spark plug. Then the ignition module circuit comes under suspicion. We remove the connector from it and turn on the ignition - voltage from the battery is supplied to contact D (photo 3 - first on the right). No 12V? We check if there is a break in the 68GP wire (diagram 2). Is there 12 V? We check the ground circuit of the module (this is contact C - second from the right in photo 3).

Most often, chain damage occurs. Failures of the controller itself are quite rare, and as for the ignition module, if the insulation of one of the secondary coils is broken, the engine, although on two cylinders, will work.

So, the algorithm is very simple: fuel pump - checking the spark on the spark plugs - checking the signal on the injectors.

Misfires on Priora

There may be no spark at the Prior due to a breakdown of the sensor, coil, spark plug or ECU. Failures that lead to loss of spark are quite easy to solve, with the exception of a breakdown in the ECU.

If the spark on a Priora disappears on all 4 cylinders, this indicates a breakdown of the crankshaft sensor in 80% of cases, in the remaining 20% the ECU may fail.

If there is no spark on one of the cylinders, then there may be several reasons - a spark plug, a coil or a transistor in the ECU.

Consider each of the reasons in more detail.

Spark plug

Quite often, low-quality spark plugs can fail after several hundred kilometers or even immediately after installation. It is recommended to purchase only high-quality spark plugs.

Which spark plugs are best for Priora can be read in our article.

You can check the serviceability of the spark plug on a special stand or by trying to replace it with a new one or by installing a suspicious spark plug in the working cylinder.

Ignition coil

Problems with the coil appear practically the same as with spark plugs. One of the windings in it may break or break through the insulation, which causes the coil to malfunction. IKZ Prioras cannot be repaired and if they break down they are replaced with a new one.

You can check the serviceability of the coil by replacing it with a coil of another cylinder or using a special diagnostic device ELM 327.

You can read how to check the coil here.

Misfire in a VAZ Priora cylinder, signs, causes

Unstable engine operation and shaking at idle, loss of power and increased fuel consumption, the appearance of a “Check” error on the instrument panel, jerking of the car and other troubles can be caused by a misfire in the engine cylinder.

There is nothing wrong with this, because if the engine runs but does not pull, it means that not everything is so critical.

Next, we will talk about how to properly diagnose a car and identify the cause of the malfunction.

Main causes of misfire

There can be many reasons for the problem; even professional mechanics spend more than one hour to identify its source.

The main reasons for misfire in cylinders 1, 2, 3, 4 can be:

The ignition coil or module has failed;
Inoperative fuel injector, clogged due to low-quality gasoline;
Incorrect spark plug gap, which can lead to poor sparking;
The spark plugs are flooded or carbon deposits have formed on them;
Breakage of high-voltage wires, increased resistance (non-standard ones are installed), oiliness of contact points;
A high-voltage wire has fallen off (often happens on Lada Kalina and Granta);
On an 8-valve engine, the timing belt may jump (during replacement, an error was made due to marks or as a result of excessive wear);
On a 16-valve engine, the hydraulic compensators are not working correctly;
Air leak (can be anywhere);
The compression in the engine cylinders has dropped or is different (applies to cars with high mileage);
Low pressure in the fuel rail as a result of reduced fuel pump performance.

Weak starter

If the Lada Priora does not start, then the possible reason is that the element is too weak. It simply cannot crank the crankshaft to the minimum 300 rpm. In this case, the required compression is not provided. Even if the starter manages to spin the crankshaft to the required speed, the engine still does not start, since all the battery energy is taken for spinning. It is not enough to operate the injectors and the ignition system.