Is it advisable to buy Mystery brand car radios: all the pros and cons of the devices

For drivers who spend a long time in the car, it is important to listen to music in good quality. The Mystery radio can provide high-quality sound. The article discusses its features, advantages and disadvantages, possible malfunctions, connection and configuration nuances, and provides an overview of the models.

Peculiarities

The popularity of Mystery car radios among car enthusiasts is largely explained by the company's pricing policy. The manufacturer maintains prices at the same level regardless of exchange rates, so device prices are affordable to a wide range of buyers. The company always monitors the latest trends in the world of electronics, which is reflected in the release of new models.

Mistreri car radios are multifunctional. Despite the large number of models, the company produces high quality devices. The peculiarity of the devices is that they can be connected to standard connectors. Therefore, any car enthusiast can do the installation independently. Car radios are equipped with connectors for connecting various digital devices that can reproduce well-known formats.

The devices are equipped with built-in processors that are responsible for sound quality and frequency. With the help of equalizers, the user has the opportunity to adjust the sound according to his taste. Models are equipped with backlighting with a choice of colors. The built-in GPS navigator makes it possible to save on the purchase of navigation devices.

The easiest way to connect

Subwoofer in the car

In this case, we mean the use of an active subwoofer, which does not require an additional amplifier. Started:

• We select a position for the subwoofer and supply power to this location. It is best done directly from the battery. If this is not possible, then as a last resort you can connect it through the cigarette lighter.

Note. It is very important to check everything correctly and maintain polarity. It is also important to additionally install a capacitor to power the subwoofer, so that when peak loads arise when playing low frequencies, problems do not arise.

• The subwoofer is connected to the car radio using a “tulip” wire or screw power contacts;
• After the connection is made, the setup will be reduced to limiting the upper limit of the speaker's low frequencies and selecting the speaker's oscillation phase.

How to connect a subwoofer

Note. Typically, many subwoofers have this feature.

A problem when connecting a subwoofer can be poor matching of amplitude-frequency characteristics. If you choose a subwoofer that has a special function that makes it possible to adjust the upper limit frequency using adjustment, then this would be considered as an advantage.

Types and models

Mystery car radios are in demand in the automotive market. Some models will be discussed below.

MDD 6270NV

This model is a radio in a stylish case with a touch screen. One of the advantages is simplicity and ease of use. The kit includes a head unit, a powerful antenna, a GPS navigator, and a TV tuner. To make it more convenient for the driver to control the device, control buttons can be installed on the steering wheel.

Pros:

• support for various devices, which allows you to listen to music from memory cards, play videos from CDs, etc.;
• for connecting devices, the radio is equipped with a USB port;
• An additional video input is provided, which makes it possible to connect a rearview camera;
• affordable price.

MMD 6220S

Externally, the receiver looks attractive, the size is 2 din. The screen is 6.2 inches, with switch buttons on the sides. The volume is changed using a knob, a similar switch for searching by radio frequency. There is a color backlight that can be changed. The choice of colors is quite wide. The appearance can be changed by selecting a picture of the car brand as the screen saver.

The radio is equipped with connectors for a rear view camera, a sambufer, a TV antenna, for reading SD memory cards, as well as a USB port and connector. The controls are simple. The time and date are displayed on the screen. At the bottom there is a button to switch the device to night mode. The device is equipped with an equalizer and a good radio receiver. It is possible to play CDs and DVDs.

MDD 7120S

The Mystery MDD 7120S car radio has a 7-inch diagonal LCD touch screen with high image quality. This model is a universal device capable of reading information in different formats and media (CD/DVD/MP3/USB). On the front panel there is a port for USB and SD cards (video by Serega Soviet).

Advantages of the 7120s model:

• standard 2 din size allows installation on cars manufactured after 2007;
• output power 4x50 W;
• the device is equipped with a built-in TV tuner that supports standards: PAL, SECAM and NTSC;
• You can install controls on the steering wheel
• the radio transmitter operates on VHF, FM and AM waves;
• On the back there is an input for a rearview camera and AV.

The radio comes with a remote control.

MDD 4310S

The model is equipped with a full-color display. Screen size 6.2 inches. Rich colors and high sensitivity allow you to watch movies and videos in good quality. The monitor clearly displays a map of the area. The powerful antenna included in the kit receives high-quality signals regardless of the location of the car.

The radio has the following technical characteristics:

• equipped with a GPS navigator;
• power is 50 W;
• device size - 2 din;
• touch screen size – 6.2 inches;
• supports a wide range of radio frequencies;
• allows you to play audio formats – MP3, WMA;
• It is possible to view video in MPEG4 format.

Functions

The TFT display switches to night mode with reduced brightness with just one touch. Touching it again turns off the screen. The user can adjust brightness and contrast manually. If you connect the ILL cable, the brightness will automatically decrease when the side lights are turned on. There is no drive for reading CDs, but this is considered the norm for budget radios.

For FM and AM radio frequencies there are 2 sets of presets (6 in each). The tuning range on the Mystery MDD-7120S radio is not end-to-end, there is no RDS decoder. When connected to an external car antenna, the tuner works, but shows a weak signal reception level.

The radio supports playback of video recordings with a capacity of no more than 1.5 GB.

The Mystery device has the following functions:

• digital tuner designed to receive stations in the VHF (FM), MW and LW (AM) bands;
• memory block for 12 VHF stations and 12 MW and LW channels;
• expansion of the ultrashort wave range with the ability to save 6 channels;
• built-in MP3 file decoder;
• possibility of cyclic playback (Repeat);
• playing songs in a mixed order (Random mode);
• digital sound volume control;
• loudness compensation and sound volume reduction;
• built-in equalizer with 3 factory settings (classical, popular and rock);
• standard remote control (with reduced thickness).

Manual

Before installing the radio in the car, you should carefully study the proposed operating manual and adhere to the recommendations specified in it. Connect according to the diagram.

Mystery radio connection diagram

Basic Connection Considerations

Before connecting, you need to disconnect the negative terminal of the battery.

The receiver should be installed away from heat sources, in a place where there is no direct sunlight, dust, dirt and large vibrations.

For connection, you should use special automotive cables and wires with the appropriate cross-section to avoid voltage drop.

The installation process involves the following steps:

1. Using special keys, you need to remove the radio from the installation frame.
2. Then the frame in which the device will be installed must be inserted into its regular place on the dashboard. The frame should be installed without any force to avoid damaging it. After installation, the frame must be secured.
3. At the next stage, you need to connect the antenna and connect all the wires and cables to the connectors according to the connection diagram, which is in the instructions for the Mystery radio.
4. Next, the device is inserted into the frame until it stops until the springs fit into the corresponding grooves.

To increase noise immunity, the car radio housing must be connected to a metal part of the body.

After installing the radio, the battery is connected. For some models, power from the cigarette lighter is sufficient, so they can be connected to it.

Setup Basics

The device is controlled and configured using buttons located on the front panel.

They have the following purpose:

• button for removing the muzzle (front panel);
• on/off;
• volume control;
• selection of operating mode;
• move to next track;
• removing the disc;
• selecting a radio station;
• buttons for turning on various playback modes;
• go to the previous track;
• selection of frequency range;
• instant sound on/off;
• system initialization (data reset).

The front panel has connectors for connecting external devices, SD memory cards, and USB.

Similar control buttons are located on the remote control that comes with the device. The purpose of the control buttons is described in detail in the car radio manual. It also describes how to correctly perform general settings, as well as set up the radio, sound, time and date, image, steering, etc.

Connection via amplifier

This assumes connecting a passive subwoofer. So, let's begin:

• The first thing you need to do is connect the power. First, we connect the negative wire to the amplifier to the GND terminal. Don't forget to connect the other end of the wire to the car body.

Note. If you do not use a set of wires, but only pieces, then remember the following rule: the negative wire should always be thicker than the positive one!

• It is recommended to pay special attention to the cable cross-section. There is no need to skimp on good nutrition;
• We further connect the positive wire to the amplifier at terminal +12. Be sure to install a fuse, preferably as close to the battery as possible. It will protect against short circuit or sudden fire;
• In those places where the wire comes into direct contact with the metal of the body, it must be protected without fail. So, corrugations and bushings, as well as electrical tape, will cope with this task perfectly.

Note. We remember that connecting to the battery occurs at the very last moment.

• We connect with the REMOTE terminal. On all modern cars, or rather, in its head unit system, there is a blue wire with a white stripe applied to it. When the head unit is turned on, 12 volts are supplied to the wire and the amplifier turns on. Accordingly, if you turn off the car radio, the amplifier will also turn off. Convenient and safe.

Note. If for some reason there is no such wire, then the REM terminal is already connected to the ACC circuit. This goal implies such a position of the key in the ignition switch when only the radio works (typical for foreign cars).

• We carry out RCA cables. They connect the sound of the car radio with the amplifier (see How to connect an amplifier and subwoofer to a car radio: you are your own master). We try to lay these wires as far as possible from other cables and other sources of interference.

Note. If there is excess cable left, then it does not need to be twisted into a ring, but it is recommended to lay it in a snake.

If the Mystery car radio has one pair of line outputs, and the connection is to a 4-channel amplifier, it is recommended to use the Y-connector. Although with this connection the fader is lost. If the amplifier has an INPUT-SELECTOR, then this is the same Y-connector. We connect the subwoofer and this operation can be considered complete.

Possible malfunctions and ways to eliminate them

Like any device, the radio may have malfunctions.

Specifications

A car radio can be called not just a practical, but also a stylish device. The design has been carefully thought out to ensure maximum user comfort.

The front panel is removable. This is done for security purposes, so even when the driver has to leave the vehicle, he does not have to worry about equipment theft. On the front panel there is an AUX output and a USB port, which allows you to listen to files from a flash drive.

The model is equipped with built-in amplifiers (4*50 W). This allows you to achieve powerful and clear sound. The driver can also use the 2 RCA preamplifier outputs to connect an additional stereo component, for example, an amplifier for the rear speakers.

The device is compact, its size complies with accepted standards: width - 17.8 cm, height - 5 cm, and installation depth - 16.0 cm.

The car radio is designed for an operating voltage of 11-14 V. The frequency range of the VHF tuner is 65-108 MHz, for a medium-wave receiver it is 522-1620 kHz. This model has 30 built-in memory cells for radio stations.

Pros and cons of devices

The main advantages of Mystery car radios:

• convenience and ease of connection;
• connector for connecting a rear view camera;
• GPS navigator;
• powerful antenna;
• wide frequency range;
• presence of an equalizer;
• high-quality sound;
• backlight

Disadvantages apply to specific models.

You can name some of them:

• not all buttons are activated;
• limited equalizer capabilities;
• inconvenient player interface;
• poor sound quality;
• few settings.

Each model has its own advantages and disadvantages.

Price issue

1. MDD 7120S (price from 3500 rub.)

2. MMD 6220S (price from 6400 rub.)

3. MDD 6270NV (price from 9800 rub.)

4. MDD 4310S (price from 10,500 rub.)

Connecting the Mystery subwoofer

Connect the mystery subwoofer to the radio

If you have a Mystery radio in your car, then there is a reason to connect a Mystery MBV-251A subwoofer to it. It is active and everything necessary for connection is included in its kit. Started:

• To begin with, it is better to check its operation at home. If the sound power is satisfactory, then everything is fine.

Note. It will also be useful to measure with a tester how much electricity this subwoofer consumes. As it turns out, when completely turned off, this subwoofer does not consume anything. When enabled, even if you turn off the bass, the speaker will consume power. Thus, it would be more appropriate to place the button on the control wire rather than on the thick positive wire.

• It's time to lay the wires. It is advisable to take the minus from the bolt securing the rear seat of the car and tighten it with a nut to ensure good contact.

Note. Laying a thick positive cable into the interior can be difficult. If you don’t want to drill the body, you can push it into the wiring harness going into the interior. In a word, decide for yourself - the easiest way is to make a hole with a drill and insert the wire.

• After the positive wire is inserted, you will need to connect it to the battery terminal (you can use a 10mm bolt);
• The remote bass control can be mounted directly above the fuse box. Here the regulator will not be conspicuous and the place is convenient, always at hand.

The installation should be carried out so that after turning on the head unit, use the button to turn on or off the subwoofer if it is not needed. Very comfortably.

Advantages of the Mystery subwoofer

This subwoofer has many advantages, the main ones being:

• Equipped with a built-in amplifier. There is no longer any need to purchase a separate amplifier and connect a subwoofer through it;
• This active subwoofer is very compact in size.

Note. In some cases, if there are reasons for this, this subwoofer can be safely placed under the car seat. It will fit comfortably there due to its small size.

• This speaker produces sound with clear low frequencies. The sound will always be clear;
• The speaker is inexpensive - only 2.5 thousand rubles;
• This subwoofer is distinguished by a stylish and attractive design;
• The body is made of aluminum, but very durable;
• The volume of the subwoofer can also be controlled from a distance. For this purpose, there is a remote control included in the kit.

The procedure for connecting a subwoofer to the Mystery radio was presented above. It is done with your own hands, using step-by-step instructions. In addition, it is important to watch video reviews of the operation and photos - materials that will give practical understanding. The asking price is low. In total, about 3-4 thousand will be spent on consumables.

Compatibility with other devices

The MAR-919U player is compatible only with external USB drives and SD cards. The volume of devices should not exceed 2 GB, the number of files should not exceed 500.

According to the instruction manual, support for external hard drives is not guaranteed. The user can connect compact MP3 or WMA file players via the AUX port. Playback control is carried out by push-button switches located on the player body.

Connection diagram

The drives are inserted into a USB connector, the user can connect an extension cable to which the devices are connected. To use an SD memory card, you need to fold down the front panel and place the part in the slot.

The drive is held in place by an automatic spring lock. To remove, you need to gently press on the visible end part, and then remove the card from the slot. Additional players are connected using a 3-pin cable, the plug of which is installed in the AUX socket.

Disc Information

Page 4

• Image
• Text

-4-

Do not use discs with labels or stickers on the work surface.

Do not use non-standard shaped discs. Use only round discs for playback on this player. The use of discs of non-standard shape will cause the device to malfunction.

Types of discs that can be played

Compact Disc Digital Audio; Compact Disc Digital Audio Recordable; Compact Disc Digital Audio Rewritable.

CD-R and CD-RW discs that have not undergone the finalization process cannot be played. (For more detailed information on finalizing the process, please refer to the software instructions for your CD-R/CD-RW disc or CD-R/CD-RW writer).

WARNING

This device is intended for the playback of exclusively legal recordings produced using established standard methods on standard optical storage media. Some titles (discs) may not be playable on this unit. This may be due to an incorrect recording protocol, recording method, parameters and settings of information compression programs, or media quality. For example: the disk has a structure other than CDFS, or the recording session has not been closed, or in accordance with the parameters and settings of information compression programs, this disk is intended for playback only on devices of a different type, or the disk on which the recording was made has optical characteristics other than standard.

DISK INFORMATION